Models > AAV7000AWW > Instructions

AAV7000AWW Admiral Washer - Instructions

All installation instructions for AAV7000AWW parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the AAV7000AWW
286-300 of 373
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

shaking & walking

  • Customer: fernando from lockport IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Wrench set
  • 0 of 0 people found this instruction helpful
i had a hard time installing springs. also it didn't fix the problem. is there another problem i have to fix so it stops shaking & walking. if so what is it ?. do you have a tool to install the spring ?.

water pump stoped working

  • Customer: donald from fillmore IN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Easy fix. I pulled the washer out from the wall and leaned the top back to the wall. I then removed the belt from the bottom. I set the washer back on all fours and slide it around so I could get to the back water pump access panel. Using a nut driver, I removed the screws from the panel, then I removed the panel. I could now see the water pump. With a pair of pliers I removed the two hose clamps, and removed the end of the hose's from the pump. Then with a socket wrench I removed the three screws holding the pump down and removed the pump. In reverse order I put it back together. It works fine and saved me a lot of money from happened to buy a new washer. Thanks PartSelect.

Noisy spin cycle

  • Customer: William from Cochiti Lake NM
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Just as shown in video on website

vibration durring spin cycle

  • Customer: jennifer from dwight IL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
follow the video on snubber ring replacement an use 1/2 inch washers keep the tub springs from collapsing then it is very easy to remove them make sure to tilt the tube assembly an un hook start to finish under 1 hour

water won't leave the washer, make laud noise and burning smell

  • Customer: Joshua from Naperville IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
remove the cable under the washer, open the back small opening/access panel, unplug two hoses, remove and replace the pump, put everything back including the cable under the washer. then test and it washes like new and quiet. Installation video is very helpful.

Hinges for the lid were broken

  • Customer: David from Chandler AZ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
The repair went smoothly with no issues or problems. The video link sent with the receipt made all the difference in the world. I watched the video on my iPad as I was doing the repair. Also locating the parts I needed on the part select website could not have been simpler.

Lid on washmachine was loose. Found that one of the plastic hinge pins had broken.

  • Customer: Larry from Woodbury MN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Ordered two new hinge pins as well as hinges. (Did not want to have to deal with it again so chose a full change out.) Watched a U-Tube video that described how to change out the hinges. The trick is find out how to lift the top panel on the washer to access the screws that anchor the hinges. Use a putty knife and slide it into the space between the top panel and the front panel. Got the job done today in an hour or so. Chose to also wipe out the top of the wash tub at the same time so it took a bit longer. Works fine now. Just like new.

Machine out of balance; banging; hopping.

  • Customer: Gary from Wellington FL
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Followed very detailed instructions posted on the website. Made a difficult job possible; without instructions would not have been to do repair. Thanks to those who posted step-by-step process. Suspension springs most difficult part of job, followed by C clamp. Lots of sharp edges to cut and scrape your arms and hands. After seeing how this machine is built, I am done with Maytag appliances.

Washer was off balance

  • Customer: Daniel from Fort Walton Beach FL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Cause:The main problem was the snubber ring got destroyed from continuously overloading the washer. That lead to the unit becoming off balance which in turn broke the belt pully off of the water pump and wore out the tub springs. Solution: Procedure 1: Make sure to turn off the water going to the machine, unplug the hoses and the power cord and if you have room take it out away from the wall. even after it is drained there will still be some water in the unit so keep a good size towel on hand. The pump is the easiest part to replace; simply lay the machine forward so that you can get to the back panel and the bottom at the same time. Remove the panel and the pump is just inside. remove the belt from the bottom of the unit then remove the black hoses from the pump taking note how they are situated and the size difference. Remove the bolts that attach the pump to the housing then lift the pump out through the opening; unless you have purchased new bolts you are going to want the old ones for the reinstall since the new pump probably doesn't come with any. Also, the replacement pump may not have the same mounting bracket but it will mount just fine without it. now simply install your new pump in the same position as the old, secure it to the housing and reattach the belt. Procedure 2: Now for the springs; this is a little more difficult and it is going to take some muscle and patience. Do not remove all of the springs at once, trust me! lol! The easiest way to do this is to remove one spring at a time and replace it with a new one; just make sure to mark them as you go or at least remember where you started. Only a few of them are accessible from the panel in the rear but if you tilt the machine back upright the whole front of the machine can be removed very easily. First you must remove the top; to do this there are two brackets on the back at the top behind the instrument panel that can be removed with a Phillips head screw driver. after they are removed pry the front of the whole top panel up, there are only two brackets holding it down. Remove the two screws that you have uncovered at the front and remove the front panel by lifting up slightly and pulling forward. you can now get to the rest of the springs. Take note how everything was removed and reverse process to put it all back together. Thanks and goodluck!

during certain wash cycles their was a burning rubber smell.

  • Customer: Jeff from Cornelius NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
lifted the front of the washer on a 45% angle,leaned it against the wall and gained access to the bottom and the belt,rolled the old belt off,it was very stretched came off easily,rolled the new one on and that was it.

The problems only put the Belt in back

  • Customer: Syed from Mcallen TX
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Wrench set
  • 0 of 0 people found this instruction helpful
The water pumps was was very easy to put it back in and I Save money And they have a video instruction to put it back in water pump This is a first time I repair something myself Everything was very helpful :)

LID WOULD NOT STAY UP

  • Customer: michael from blanchester OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
TOOK OF LID,TOOK OUT SCREWS,PUT ON HINGE AND PINS,SIMPLE JOB

Agitator Broken

  • Customer: Barry from Spartanburg SC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Socket set
  • 0 of 0 people found this instruction helpful
Replaced agitator in less than 30 minutes with ratchet and socket. Fast delivery from vendor. We are up and running again!! Very pleased.

loud noise when spinning

  • Customer: Brian from Allison Park PA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The video is really helpful. The clamps on one of the hoses slowed me down. It took some contorting to get the clamps compressed and at the right angle to secure the hose. My lack of patience was probably the culprit. FYI: My failed pump made no grinding sounds. Nor was there any resistance when turning the pulley. But the problem was indeed the pump. Working well now.

Washer was squealing when agitating & spinning

  • Customer: Jan from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
All that had to be done was pull the washer out from the wall, tilt it back and roll the belt off one of the three pulleys and it fell right off of the other two. To install the new belt place it around two of the pulleys and roll it over the edge of the last one. Actually took 15 seconds to change it. Getting the washer out and ready took the most time. Now there is NO noises when it agitates or spins. LOVE IT!
All Instructions for the AAV7000AWW
286-300 of 373