Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AAV4200AWA

AAV4200AWA Admiral Washer - Overview

Get Parts and Repair Help for AAV4200AWA

If you know the washer repair part you need, you can browse the list of all parts on the AAV4200AWA, or you can search by name or part description. You can also find your part by where it is located on the AAV4200AWA by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AAV4200AWA parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$3.34

Suspension Spring

This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.

$9.88

Drive Belt - 51 inches long

This V-style drive belt measures 51 inches long and 3/8 inches wide. The belt is made to slip on the motor pulley to bring the basket up to the speed required. Continued use can result in the belt suffering from wear and tear. Replace the V-style drive belt if you notice that the belt looks damaged. The most common symptoms of a damaged drive belt include: a burning smell or a loud grinding noise coming from the washer; the drum will not spin, spins slowly, or not agitate; the washer shakes and moves, will not start, or will not drain.

$5.26

Snubber Ring

The snubber ring is a piece that is specific to your washing machine. The function of the snubber ring is to reduce noise and vibrations within your washer. It fits in between the ...

$52.97

Transmission Pulley and Bearing Kit

This transmission pulley and bearing kit, also known as thrust bearing kit or washer pulley and bearing kit, includes the pulley, washer, thrust bearing, two upper race washers, and one lower race washer. These genuine Whirlpool parts are plastic and are not sold individually. The kit is used to help the washer drain, and may need to be replaced if the washer is experiencing slow or no spin, will not drain, or has no agitation. The washer will need to be tilted on its back or side to access the bottom. The tools needed to complete this repair are a small flat blade screw driver and a pair of slip joint pliers.

$72.17

Drain Pump with Pulley

This drain pump with pulley, also known as the washing machine drain pump assembly, is a pump with two ports. The function of this pump is to help expel water from your washing mac...

$3.02

Cover Screw

Sold individually.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$9.64

INLET HOSE

This hose can handle hot or cold water and is five feet long.

$17.90

Tub to Pump Hose

Hoses are the most likely cause of clothes washer leaks. This tub-to-pump hose carries the water from the tub to the drain pump. If you notice that your tub is leaking during the w...

$5.51

Hose Clamp

The hose clamp is used to hold the water hose in place which will prevent the hose from leaking water. Sometimes the clamp may lose its ability to latch on, causing a leaking washer. For the installation, you will need a flat head screw driver to replace the clamp and a drill to access the screws to remove the front of the washer. Be careful if you do not have specific clamp pliers as the clamp could fly off. Once the front of the washer has been removed, take a quick look for water damage or any obvious signs of where the leak is coming from. If it is not obvious, run water to test.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 536 of 541 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

Washer jumping in spin cycle (white flakes under the washer)

  • Customer: David from Butler, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 248 of 257 people found this instruction helpful
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of... read more

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey, FL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 134 of 146 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more