Quick Question!

Have you ever purchased from PartSelect.com before?

Models > AAV1200ARW

AAV1200ARW Admiral Washer - Overview

Get Parts and Repair Help for AAV1200ARW

If you know the washer repair part you need, you can browse the list of all parts on the AAV1200ARW, or you can search by name or part description. You can also find your part by where it is located on the AAV1200ARW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AAV1200ARW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$6.77

Snubber Ring

$7.88

Lid Hinge

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

$5.15

Suspension Spring

This suspension spring is used with many washing machines. It is made entirely of metal and is seven inches long.

$12.18

Lid Hinge Pin

This lid hinge pin is just over an inch long. It is all white in color and is made entirely of plastic. Sold individually.

$70.15

Drain Pump with Pulley

This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$52.97

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are NOT available separately - they are ONLY available in this kit. A worn bearing causes slow or no spin.

$5.15

Hose Clamp

$5.10

Screw, 8/18 x 3/8

This screw is sold individually.

$5.51

Hose Clamp

This hose clamp is sold individually.

$5.15

Cover Screw

Sold individually.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washing machine was making alot of noise

  • Customer: David from Boca Raton, FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Wrench set
  • 529 of 534 people found this instruction helpful
I found the water pump bearings were going bad from humidity. I replaced the pump with a new one and it runs quiet again. read more

One of the plastic hinge pins brroke

  • Customer: Allen from North Little Rock, AR
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 482 of 480 people found this instruction helpful
I used a flat screw driver to push in on the releases so I could raise the top of the machine. I then used a torx tool to remove both parts of the hinge, and then used a #2 phillips screw driver, on the new screws I'd also ordered, to re-attach both of the hinge parts. Every thing went just as anticipated. read more

Washer jumping in spin cycle (white flakes under the washer)

  • Customer: David from Butler, PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 238 of 247 people found this instruction helpful
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of... read more