Models > AAV1200AJW

AAV1200AJW Admiral Washer - Overview

Get Parts and Repair Help for AAV1200AJW

If you know the washer repair part you need, you can browse the list of all parts on the AAV1200AJW, or you can search by name or part description. You can also find your part by where it is located on the AAV1200AJW by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for AAV1200AJW parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$4.05

Lid Hinge

This lid hinge in an inch and a half long and is used for some washing machines. It is all white in color and it is made entirely of plastic.

$4.75

Snubber Ring

$3.96

Suspension Spring

Sold individually.

$69.70

Drain Pump

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This is a redesigned part. The pump now mounts on to the base of the washer - no mounting plate needed.

$44.48

Drain Pump with Pulley

This pump has 2 ports. This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time.

$7.46

Lid Hinge Pin

$36.18

Transmission Pulley and Bearing Kit

Also known as Thrust Bearing Kit. This kit includes the pulley, washer, thrust bearing, 2 upper race washers and 1 lower race washer. These parts are not available separately - o...

$29.48

Suspension Springs - Kit of 6

$2.70

Screw

This screw is sold individually.

$2.70

Hose Clamp

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer jumping in spin cycle (white flakes under the washer)

  • Customer: David from Butler PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 131 of 139 people found this instruction helpful
Unlug the AC cord,open the top from the front it snaps open with a little force and hinges on the back, remove the 2 screws on the front cover and take it off, tip the washer and remove the belt, take off the pump hose from the back (I removed the back cover also) and the little hose going to the basket. Remove the 6 springs and lift the complete drum out of... read more

Load Grinding/Rubbing Noise in Rinse and Spin Cycles

  • Customer: Doug from Port Richey FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 111 of 122 people found this instruction helpful
First unplug the washer for the electrical outlet. You will need to tip the washer back to get to the bottom of the machine. There you will see the belt that drives the transmission and the water pump from the motor. Remove the belt and set it to the side. Then you will need to gain access to the top side of the machine by gently using a screwdriver to pry... read more

EXCESSIVE Banging, shaking and squeaking while on Spin Cycle

  • Customer: robert from simpsonville SC
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers
  • 63 of 66 people found this instruction helpful
1)Start with empty washing machine.
2)Disconnect Hot, Cold, Power and Drain lines
3)Move machine to open area, open top by popping 2 front retaining clips.
4)Remove Front panel, remove small clear water level hose at lower rear of tub.
5)Remove small Rear access panel, disconnect large tub drain hose from pump and drain into small contain... read more