AAV1100AWW Admiral Washer - Instructions

I watch the video and it took me less than five minutes to change the drive belt. The washer has been running great and no more burning smell. Thanks.

I borrowed a 13mm socket wrench. Removed the softener dispenser, prying it off with a flat screwdriver. Unscrewed the 13mm bolt, lifted off the broken agitator, placed the new agitator in place and bolted it down. At that point, the dispenser simply snaps back into place. Very simple replacement.

Remove all hoses and power supply tiled washer towards the front. By removing four screws to rear access panel on the back of washer to gain access to drain pump. Removing drive belt and releasing hose clamps. With socket wrench or nut driver remove three screws to remove pump from washer base. Replaced with new drain pump is a reverse to removing old pump.

Just like the viedo said, release the springs holding the top, remove the screws and replace the hinge. Put the top back on by snapping back into place.

Took off pre wash vessel from top of agitator. With the aid of a small socket unbolted and removed agitator. Fitted new replacement, took less than fifteen minutes, including unpacking the new part. The delivery of which was incredibly quick.

I don't think I have a lot to add, there are some great instructions and comments already on the site. Our washing machine is getting a little old but this was a fairly easy fix. Our washing machine was constantly off balance and walking across the floor. I can't believe how much of a difference these little parts made. It saved us a ton of money so thank you PartsSelect!

was really easy. I watched the video and was done in less than 10 minutes. I read other stories and pushing the tub over and removing and installing the screws would have been very difficult. Opening the lid was very easy then the screws are right there in front of you.

After pulling the front panel off the washer, I determined the source of the smell and smoke to be the motor. I reviewed partselect.com troubleshooting page for burning smell and found that the motor was the second highest cause for this occurence. The first was a worn belt. I was certain it was the motor, but double checked the belt. The belt is still good. My next step was to watch the video on partselect.com to determine if this was a project within my capabilities. After viewing the video, I placed my order with standard shipping on Thursday at 10pm est. The motor arrived on Tuesday evening via UPS at 6:00 pm. I started the installation at 9:30 pm after the kids were put to bed. The dismantling and reinstallation was exactly as viewed on the video. By 10 pm I was reinstalling the front panel. This was two weeks ago with an average of 2-3 loads a day and not another issue with the burning smell or smoke. Partselect.com saved me a couple hundred dollars in appliance repair service costs and several hundred if I would have purchased a new washer. I will definately keep partselect.com in my favorites for the next appliance repair.

real easy ,turned it over on it front , the bump and belt are on the bottom of washer 3 outside screws to remove plate cover, 3 bolt to remove pump, 2 clamps on hoses, im done, works grate tks. partselect. for fast shipping and having them in stock.

unscrewed back cover 3 screws then unscrewed 3 screws holding pump, pulled off belt replaced pump, put screws on, and then belt, then turned on machine no problems, put back plate on and it worked ...great job , I did this with 1 are in a sling so that's why it took 1 hour..

Initially, it was uncertain how to remove the front panel. There were hidden clips that I was unaware of. But, the video on partsselect's website was excellent. It gave me the confidence exactly what to component to purchase and how to repair my washer. My repair was identical to the drain pump video and had no issues what so ever.

Disconnected hoses and power cord, pulled washer into hall area, laid towels down to soak up any residual water and tilted washer onto its face or front side. Removed lower panel on back of washer with three screws to expose pump and hoses, removed belt from underneath, removed three screws from pump base with nutdriver and two hoses with spring clamps with pliers. Installed hoses with spring clamps with pliers, slid pump into place per alignment pins on the base, installed the three screws on the pump base with nutdriver, installed rear panel with three screws with nutdriver. Installed belt and titled into upright position, slid back into place, hooked up the hoses then cord and did a load of laundry just like it was new.

Followed video instructions. Most difficult part was re-installing the E-clip on the bearing.

Tilt washer back to expose the bottom. Remove broken belt. Install new one. Do a test run: Washer is back to working fine. Note: My boyfriend actually did the repair while I was at work, but reported that I could have done it myself easily. Also: FedEx delivered the part on a Saturday without an extra delivery charge, so my washer was repaired several days sooner than I anticipated. Thanks, PartSelect!

just a matter of 1 screw to remove and replace part ordered part 1 day and came in next day with regular mail. was a surprise for my daughter, she went on vacation and i fixed while she was gone. she was using different items to place in slot to engage each cycle.