A806 Maytag Washer - Instructions

I suspected the pump, so, once I removed it, it was obvious that the shaft from the pump pulley to the impeller was broken (the pulley turned, but the impeller was not turning).I ordered a genuine "Maytag" pump from Parts Select, even though it cost me twice as much as other pumps advertised on Amazon.com. Why fool around? While I was at it, I also ordered 2 new belts from Parts Select, even though the belts on the machine looked OK. But heck, the old belts were 26 years old! What a great machine this old Maytag! This is the first time in 26 years that it failed me...The only reason I looked at the Parts Select repair video was to know what tension to put on the pump belt...BTW, I ordered the parts on the weekend, and they were sitting on my front porch Tuesday, early morning. Impressive..

pulled out wash/dry stacked combo unit from cubbyhole (this was the hardest part) . Shutoff both hose supplies, turn off power to unit.disconnect power cord @ coupling. Disconnect both hoses @ machine and drain into pan. Remove old valve assembly,take note of what wires go where and disconnect. Remove filler hose from valve. Install new unit in reverse order but using new hose washers and be carefull not to cross thread the plastic threads and only tighten as much as needed to keep from leaking. Have bought from these people before and they are SUPER. Had the correct part in LESS than 24 hrs. and for a reasonable price !! Sam

I tried to get an appointment with our local appliance repair company, but they cancelled and wouldn't reschedule at a convenient time, so I decided to do it myself. Determined that the Mounting Stem/Tub Seal kit was the needed part and ordered it here. Also had to order the specialty spanner wrench from another website. Parts were delivered in a timely manner. The online video was very helpful and the removal and replacement of the defective part went smoothly. The only problem with the actual repair was with removing the old tub seal gasket -- it took quite a bit of coaxing to get it free. The new parts went in with no problems. However, we have an older model than the one shown in the video -- it has the metal tub top cover with the rubber gasket and ring clamp. This cover is tricky to replace properly. It has to be at just the right height to avoid interference with the spinning inner tub (too low) or with the washer lid (too high). You also have to make sure that the rubber gasket it not twisted or crimped by the ring clamp. It took me three tries to get this just right. After that, everything worked fine and the leak is fixed.

Be very, very careful not to cross thread the filler hose, onto the nylon valve housing. Recommend some lubrication, and a pair of velvet gloves.

Removed old hose and replaced with new one.

Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

I got all of my repair information from your website. I started with 'Maytag washer leaks' and found out that, statistically, the rubber injector valve was the first most likely leak source. Then, to check if this was actually the leak, I lifted the top of the machine during the fill cycle, and watched the water spritzing from the housing that enclosed the Rubber Injector Valve. Next, I watched one of your repair videos associated with replacing the valve. Next, I ordered the part from you. When it came, I installed it. The whole process, from beginning to end, was very good.

Removed the old one installed the new one

Replaced the pump. The front panel screws were rusty. I also replaced the belts at the same time. The repair video told me just what to do. I wouldn't have known about the belt tension otherwise.

Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Same technique as the PartSelect video, except the result leaked to the outside at the outlet port because the two halves of the mold that made it were slightly misaligned, and there were two steps, one on each side of the fitting. Filed the steps away, and used Evinrude gasket sealant to make sure it wouldn't leak, and it didn't.

My husband did the repair. Since he owned a laundry quite a few years ago, he knew what he was doing. After hooking everything back up, the cold water was coming in hot. When hooking up the hoses, he had hooked the cold into the top intake. After watching the online video, he realized that the plate that was to be installed over the hoses, on the back of the washer, clearly stated "H" on top and "C" on the bottom. So we switched the position of the hoses and everything ran perfectly after that. I would suggest to ANYONE doing this repair, to watch the online video first, before starting, because it is very, very helpful.

Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.

I watched the YouTube video twice and it was just as easy as in the video. No problems. I ran a couple of test loads and it was back working like a champ. My parents had their belt changed by a repair man and it cot them $150 (pretty reasonable). This whole repair cost only $45 and 15 minutes (including the video watching time!). It pays to do the simple things.

I unplugged machine and removed water and clothes. Tipped washer bback to gain acccess to belts, which slipped off and back on quite easily. Put washer back in place, plugged in and continued washing clothes. Simple!