Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A7500 > Parts

A7500 Maytag Washer - Parts

All parts for models starting with A7500

Below is a list of all Maytag Washer parts for the models starting with A7500. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

Models starting with A7500

All Parts for models starting with A7500
1-14 of 244
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.68

Belt Kit

This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these bel...

$35.76

Water Inlet Valve

This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for this repair are: a 5/16 nut driver, 1/4 nut driver, and a small flat blade screwdriver. If cold water does not flow into washer, or the washing machine will not fill with hot water, replacing the valve can be the solution. To gain access to the water valve, locate the back of the washer and remove the hot and cold hoses, as well as the whole assembly. Next, remove the four wires and loosen up the clamp. After removing the old valve, replace it with the new one and reconnect the wires and hose. Remember to disconnect the washer from the power source before starting this project.

$3.02

Screw

This screw is sold individually.

$10.56

Rubber Injector Valve

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in length. To access this part, you will need to remove the front panel of your washer. There will be 2 screws holding it in place. Once these have been removed, the top will pivot to open, which will give you access to the injector assembly. This is an OEM part that comes right from the manufacturer and is sold individually.

$52.16

Mounting Stem/Tub Seal Kit

This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should ...

$9.32

Plastic Injector Nozzle

The plastic injector nozzle is used in washers and dryers. It is 3 inches long and is white in color. If your washer is leaking water, replacing the nozzle could solve your problem. For this repair project, you will need a 1/4 nut driver, 3/8 socket with extension, and a stubby Phillips screwdriver. To begin the repair, first remove the front panel by removing screws from the bottom end of both sides. Next, locate the two bolts in the interior of front panel and remove both. Pull bleach dispenser hose off before removing the top cover of washer. Remove clamp that holds the hose to the valve assembly to access the nozzle inside rubber valve and replace with new nozzle. Refer to the instructions provided by the manufacturer for further guidance.

$6.08

Rubber Foot Pad

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place....

$22.81

Damper Pad Kit

This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.

$19.42

Syphon Break Elbow Kit with Clamp

For drain hose 7/8".

$19.19

Lid Switch

This 3 prong lid switch is used for washing machines that do not have a tub light.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air...

$20.30

Lid Check Switch

This is used to start your washer once the desired water level is reached.

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...

$5.05

Washing Machine Lid Hinge Ball

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Maytag brand washing machines.

All Parts for models starting with A7500
1-14 of 244