Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A702S

A702S Maytag Washer - Overview

Get Parts and Repair Help for A702S

If you know the washer repair part you need, you can browse the list of all parts on the A702S, or you can search by name or part description. You can also find your part by where it is located on the A702S by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for A702S parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$50.48

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace t...

Order within the next 9 hrs and your part ships today!
$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 9 hrs and your part ships today!
$48.36

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Order within the next 9 hrs and your part ships today!
$23.74

Glide and Spring Kit

This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.

Order within the next 9 hrs and your part ships today!
$5.15

Tension Springs -Set of 2

This is a set of 2 tension springs.

Order within the next 9 hrs and your part ships today!
$37.80

Water Injector Hose

This water injector hose is the hose found at the top of the tub cover of some clothes washers.

Order within the next 9 hrs and your part ships today!
$5.92

Hose Washer and Screen Insert Kit

The hose washer in this washer and screen insert kit is an inch in diameter. The insert is all blue in color and is made entirely of plastic, while the washer is all black in color...

Order within the next 9 hrs and your part ships today!
$174.69

2-Speed Drive Motor with Jumper Wire

This two speed split phase washing machine motor performs 1725 revolutions per minute in one speed and 1140 revolutions per minute in the other speed. This motor runs at 1/2 horsepower and it carries 8.0 amps. It's a good idea to change your washer's belts at the same time as you replace this motor, as they may have become worn as well.

Order within the next 9 hrs and your part ships today!
$25.20

Lid Plunger & Bracket Kit

This kit is part of the lid switch mechanism and will stop the spin cycle if the load is unbalanced. When you lift the lid, it resets the plunger and your cycle will resume.

Order within the next 9 hrs and your part ships today!
$56.34

Upper Outer Tub Cover Clamp Kit

This clamp does include the nuts and bolts to hold it together but it does not include the rubber seal. Sold separately.

Order within the next 9 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 404 of 414 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 220 of 115 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Clothes would come out of the spin cycle still wet

  • Customer: William from Cary, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 70 of 38 people found this instruction helpful
First found out where the belts were by tipping the machine backwards and saw that the belts were intact but extremely loose. Ordered two belts (Drive and Pump) . Re-tipped the machine and in less than three minutes, had installed the new belts. I re-hooked the hoses to the back and the machine operated as if new. read more