Models > A6910

A6910 Maytag Washer - Overview

Get Parts and Repair Help for A6910

If you know the washer repair part you need, you can browse the list of all parts on the A6910, or you can search by name or part description. You can also find your part by where it is located on the A6910 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for A6910 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$14.40

Drive Belt

This rubber V-style drive belt drives a washer's transmission.

$16.64

Pump Belt

This V-style pump belt is typically used with washing machines that use two belts. This belt is about 40.5" long and 3/8" wide. This pump belt helps turn the pump and to help make the washer agitate properly. It is generally positioned between the motor and the pump.

$33.66

Water Inlet Valve

This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.

$67.86

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

$9.60

Rubber Injector Valve

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle.

$54.85

Drain Pump

This assembly uses 2 belts. Order belts if you notice wear and tear.

$2.70

Screw

This screw is sold individually.

$4.06

Plastic Injector Nozzle

$19.95

Dryer Door and Washer Lid Switch Kit

This kit is simple on/off mechanism that prohibits the machine from operating when the door is open.

$3.76

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 287 of 296 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Cold water valve only opened to a trickle

  • Customer: Brian from El Cajon CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench(Adjustable)
  • 97 of 102 people found this instruction helpful
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off... read more

Leaking water

  • Customer: Joseph from Plano TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 90 of 102 people found this instruction helpful
Well, I found the washer leaking water from the bottom a couple weeks ago. I finally got around to pulling off the front panel and ran a couple cycles to see where the water was coming from. Turns out the leak was at the plastic pump that does the draining after wash and rinse.

So I got the model number and googled online. I found Partselect an... read more