Models > A5651XRS > Instructions

A5651XRS Admiral Range - Instructions

All installation instructions for A5651XRS parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the A5651XRS
1-15 of 262
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

No heat - element had burst.

  • Customer: John from Marion IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 225 of 289 people found this instruction helpful
Unscrewed 2 screws holding terminal ends of the element in place. Eased the element out, until the two AC power wires were exposed. Pulled off the connectors from the element terminals (pretty tight fit - needed pliers to remove one of them).

Slipped the connectors onto the new element terminals, and eased the element back into the oven wall. Secured the element with the two screws removed previously, and that was pretty much all there was to it. Closed the circuit breakers, and the element tested OK.

Overall, a no-sweat job. One thing, though: I squeezed the oven connectors tight before pushing them back onto the new element. They had loosened up somewhat after pulling them off. A tight connection here seems pretty important, as arcing and corrosion could occur over time if they're too loose.

Bake element burnt out

  • Customer: Glenn from Jupiter FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 117 of 180 people found this instruction helpful
Before you touch anything unplug the range or trip the breaker. Pull the racks out of the oven, it gives more room to work. Remove the two screws that hold the element and pull the element out about 2-3". Disconnect the old element. Before you install the new element check the wire and the connectors for age and heat damage. If the connectors are loose replace them (2 connectors @ $1.97 is better than a short in the oven). If the insulation on the wire is degraded (brittle, flaking, brown) consider changing out the wiring. This means opening up the back of the oven and that is another chapter. In most cases you can just re-connect to the replacement element and attach it back to the oven with the two screws. I ran the oven to 400 degrees to just check that everything was OK. Spent a couple extra minutes to check everything out and save yourself pain later.

Heating Element would not heat up for Baking

  • Customer: Karen from High Springs FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 81 of 84 people found this instruction helpful
Removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires and then replaced the new heating element by connecting the wires and then placing the screws back in. Was a lil difficult because this unit has no oven light and it required a flash light.

Stove top element not working due to bad receptacle.

  • Customer: Richard from Carthage NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 84 of 93 people found this instruction helpful
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

The original heating element shorted and caught fire

  • Customer: Eric from Tooele UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 82 of 143 people found this instruction helpful
The repair was simple; I removed just two screws, pulled out the wires, and slipped the two spade connectors off the original element. The repair was simply the reverse of the disassembly. The only thing to remember is to throw the circuit breaker before handling the electrical connectors. Other than that, it couldn't be any more straight forward.

Replaced drip bowls in stove

  • Customer: Liza from College Point NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 64 of 125 people found this instruction helpful
Took out the old drip bowls and replaced with new bowls.

Rented appartment in which none of the drain pans were the proper size making it very difficult to cook

  • Customer: Grace Mary from Canton OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 64 of 126 people found this instruction helpful
I removed the element and then the drain pan and replaced with the new correct pans. I replaced the element and all was well.

The Burner was getting too hot and you could not regular the tempature

  • Customer: Dennis from Hagerstown MD
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 24 of 26 people found this instruction helpful
Moved the Appliance out unplugged it and removed the backing plate then Remove the Knob and unscrew the infinite switch then marking the 5 wires to know where the go on the new switch, removing and replaced it with the new one

Oven rack lost in a garage fire

  • Customer: Bob from Saint Clair Shores MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 13 of 16 people found this instruction helpful
First I opened the door to the oven. Then I opened the box that the part came in. (knife) I then slid the oven rack out of the box and unwrapped the plastic, being careful not to bend or scratch the new rack. Now, this is the tricky part... I had to move the existing rack down one space to make room for the new one. Then carefully slid the new rack in, tipping it slightly and sliding it in. LOL

worn out door seal

  • Customer: Stella from Charlotte TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 11 of 12 people found this instruction helpful
removed old clips and remaining parts of old seal...new part already had clips attached, so just snapped them into holes in oven door.

element went bad..started burning like a weld

  • Customer: Randall from Williamsburg OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
Turned off the power at the breaker box. Removed the two screws, pulled the element out about 3 inches, disconnected the two wires, reconnected the two wires to the new element, inserted element back into place, screwed in the screws...all finished...works great! Delivery was super fast...just a great experience all the way around.

bake element cracked

  • Customer: Ruth from Moyock NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 13 of 18 people found this instruction helpful
Being a woman, I first cleaned the oven. Removed two screws holding the element in place. Pulled element out about 3 inches and disconnected one clip attached to a yellow wire another clip attached to a green wire. Put new element in connected clips. Replaced screws.

Burned terminal block and filter board

  • Customer: Joseph from Decatur GA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 22 of 46 people found this instruction helpful
Removed and replaced above named parts, rewired.Be sure to tighten all nuts that secure wires. I believe this is what caused the problem.

The oven would not heat properly

  • Customer: Philip from Edgewood KY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 10 of 11 people found this instruction helpful
Pulled the oven away from the wall. Removed two screws inside the oven. Pulled old heating element out. When I did I heard a loud pop and and saw smoke. I assumed the element would not be electrically live if the oven was not on. That was obviously incorrect. I pulled the plug and then completed the installation. I went to chruch on Sunday and thanked God that I was not electrocuted. Now the oven works fine. My wife wanted the oven to die so that she could get a new alppliance, Instead I am alive.

Seriously your service was great. Your web site pointed me to the correct part, and it arrived the next day! I would definitely use your service again if I remember your name.

The oven stopped heating

  • Customer: GENE from TRENTON SC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 9 of 10 people found this instruction helpful
First I swiched off the circuit breaker just to be safe.Then I removed the two mounting screws and disconnected the the element leads. Very easy task, approx 5 mins. THANKS
All Instructions for the A5651XRS
1-15 of 262