A410 Maytag Washer - Instructions

Removed hoses and inlet valve from washer, replaced inlet valve by attaching the electrical connectors, reattached new water lines, returned inlet valve to its place in rear of washer. Checked for leaks, washed a load of clothes, everything worked properly.

My nephew followed directions in the repair video. Washer no longer leaks when warm water is specified.

I wached the six min. Video you sent me,so helpful what a great idea so the job only took me about five min. Thanks Mike

After watching the video on PartSelect, I ordered the part and received it the next day! The hoses involved were over 24 years old and is the only reason it took longer than about 10 minutes. The hot water hose was dificult to remove. Once I removed the hose, the old water inlet valve was replaced with the new valve within minutes...quick as per the video. The washer is back and was down for less than 1 full day.

Shut off hot and cold water supply and removed hoses from mixing valve. I unplugged the machine and removed the screw holding the plate that the valve is connected to. I removed the plate and valve and used my smart phone camera to photograph the wiring connections. The next step included removing the wires, the hose and clamp. Remove the valve from the plate. Reverse the procedure for installation. Make sure that the valve and plate are adjusted as far from the drum to prevent contact when the machine is going through spin cycles. The procedure took about 10 minutes and fixed the problem. You have to love Maytag for their reliability and ease of maintenance.

I took the front panel off and was able to easily access and remove the leaking drain pump. Then I propped the front of the washer up onto some boards so that I could put the two pulleys back onto the new pump, then I just tightened the three bolts in order to tighten the pulleys. However,when I started another load of wash there was a leak in the bottom of the tub, so I removed the new pump and went out and bought a new washer, figuring that our 13-year-old Maytag was going to cost more to fix than to buy a new washer. Then I wrapped up the new pump and sent it back. Thanks for all your help and for letting me send back the new part...I received confirmation of my refund today. Bob Trautman

Disconnected the electric plug and removed the water hoses from the washer. Took off the old water inlet valve under a plate on the washer and hooked in the new one. As we dismantled each section of the valve hook-up we connected that area of the new valve to be sure we got it connected correctly.

real simple i just layed it down and replaced the belts DWIGHT SHAW PS. NO TOOLS REQUIRED.

Remove the front panel by removing the screws at the bottom of the panel; remove the screws holding top and swing back on hinges; loosen the screws on the back holding the valve and replace the valve following how the defective one was attached and then reverse the operation.

tilted the machine back 45 degress. took both belts off and replaced them with the 2 new ones. put some tension on the drive belt and put the machine back in place, did a test run and it worked great.

removed 2 screws holding on front panel,tilted machine back and remover belts checked stretch against new belts.stretch was minimal.removed 3 screws of pump from underneath machine.pump impeller was free slipping replaced pump installed new belts reattached front cover& started washing clothes again.less than 15 min to do everything

I watched the YouTube video twice and it was just as easy as in the video. No problems. I ran a couple of test loads and it was back working like a champ. My parents had their belt changed by a repair man and it cot them $150 (pretty reasonable). This whole repair cost only $45 and 15 minutes (including the video watching time!). It pays to do the simple things.

I unplugged machine and removed water and clothes. Tipped washer bback to gain acccess to belts, which slipped off and back on quite easily. Put washer back in place, plugged in and continued washing clothes. Simple!

Just as the video described.... Unplugged the machine, turned off the water, both hot and cold. Unhooked the hoses (replaced them at this time since they were over 5 years old). Took out the top screw holding the frame piece and removed from machine. Took off the wires and the output hose. Removed the valve ass'y from the frame piece. Matched new to the original and reassembled in reverse order.

Ordered replacement water inlet valve, switched out within 10 mins and problem solved for less than $50. Maytag design easily allowed for the inlet valve unit to be replaced without accessing interior workings of the washer. The unit is mounted with 3 screws on a removable rear panel where the hot and cold H2O hoses are connected. Very easy! Tested immediately upon completion and was delighted to see that hot, warm and cold water filled the tub extremely fast, the way it worked when purchased new 18 years ago. The web site repair video was key to my success.