Models > A312

A312 Maytag - Overview

Parts and Repair Help for models starting with A312

If you know the repair part you need, you can browse the list of all parts for models starting with A312, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your . We’ve also included any installation videos we have for A312 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with A312

Exact Part matches for your search term

[Viewing 2 of 2]

Motor Driven Rotisserie Unit

This part number matches the current model number "A312".

Manufacturer's Number: A312 Motor-driven rotisserie unit for Designer Line Jenn-Air cooktops. Requires outlet, fits over electric grill element. Works with the following models: C206 | C236 | CCR466 | CCS446 | CVE4180 | CVE4270 | CVE4370 | D156 | S136 | S156 | S176 | SU146 | SVE47100 | SVE47500 | SVE47600 | SVE87600 | May not be exactly as shown.

Motor Driven Rotisserie Unit

This part number matches the current model number "A312".

Manufacturer's Number: A312 Motor-driven rotisserie unit for Designer Line Jenn-Air cooktops. Requires outlet, fits over electric grill element. Works with the following models: C206 | C236 | CCR466 | CCS446 | CVE4180 | CVE4270 | CVE4370 | D156 | S136 | S156 | S176 | SU146 | SVE47100 | SVE47500 | SVE47600 | SVE87600 | May not be exactly as shown.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$22.75

Water Inlet Valve

This part has two ports for water to enter. It is blue and is intended for use with many washing machines and comes with a multi-mount bracket and an outlet adaptor.

$49.07

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

$2.71

Screw

This screw is sold individually.

$9.21

Rubber Injector Valve

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle.

$44.79

Oven Rack

Used in the lower oven. Sold individually.

$2.71

Screw

This screw is sold individually.

$2.71

Hose Clamp

$47.77

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

$11.71

Thermostat Knob

This knob accepts a D-shaped shaft.

$20.79

Syphon Break Elbow Kit with Clamp

For drain hose 7/8".

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 398 of 408 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 209 of 110 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Cold water valve only opened to a trickle

  • Customer: Brian from El Cajon, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Wrench (Adjustable)
  • 156 of 164 people found this instruction helpful
I started by unplugging the appliance and then shut off the hot and cold water faucets then I disconnected and drained the hoses. Next, I removed the two screws that held the valve assembly in place. I then pulled the assembly out about 3 inches and disconnected the two wire plugs. The last step was to loosen the hose clamp on the outlet hose and pull off... read more