Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A26CAE > Parts

A26CAE Maytag Washer - Parts

All parts for the Maytag Washer A26CAE

Below is a list of all parts for the Maytag Washer A26CAE. To find the repair part you need, you can browse the list below or you can narrow your choices by searching for a part by name or description.

All Parts for the A26CAE
1-14 of 221
Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.68

Belt Kit

This kit includes both the drive belt and the pump belt which are both V-shaped. If your washer does not toss, spin, or drain water properly, this might be because one of these bel...

$35.72

Water Inlet Valve

This is a water inlet valve which is used in washing machines. The valve controls and monitors the flow of water into the washer. It has a multi-mount bracket and outlet adaptor. The tools needed for this repair are: a 5/16 nut driver, 1/4 nut driver, and a small flat blade screwdriver. If cold water does not flow into washer, or the washing machine will not fill with hot water, replacing the valve can be the solution. To gain access to the water valve, locate the back of the washer and remove the hot and cold hoses, as well as the whole assembly. Next, remove the four wires and loosen up the clamp. After removing the old valve, replace it with the new one and reconnect the wires and hose. Remember to disconnect the washer from the power source before starting this project.

$10.56

Rubber Injector Valve

This part is commonly known to cause a leak at the top left corner of the outer tub. It fits over the injector nozzle. It is black in color and measures approximately 2 inches in l...

$3.02

Screw

This is a multi-use and multi-appliance screw. It can be used on a microwave, refrigerator, range/oven, air conditioner, dehumidifier, washer, or dryer. The measurements of this screw are 8 x 1/2 inch. It has 6 threads. Refer to the manual provided by the manufacturer for further information on repair and accurate guidance. Remember to wear work gloves as a safety precaution.

$52.49

Mounting Stem/Tub Seal Kit

This kit comes with a hub assembly, agitator seal, and spanner nut. If your washer leaks once it is full (with or without clothes in it) or leaks during agitation, then you should ...

$9.32

Plastic Injector Nozzle

The plastic injector nozzle is used in washers and dryers. It is 3 inches long and is white in color. If your washer is leaking water, replacing the nozzle could solve your problem. For this repair project, you will need a 1/4 nut driver, 3/8 socket with extension, and a stubby Phillips screwdriver. To begin the repair, first remove the front panel by removing screws from the bottom end of both sides. Next, locate the two bolts in the interior of front panel and remove both. Pull bleach dispenser hose off before removing the top cover of washer. Remove clamp that holds the hose to the valve assembly to access the nozzle inside rubber valve and replace with new nozzle. Refer to the instructions provided by the manufacturer for further guidance.

$6.08

Rubber Foot Pad

The leveling leg pad or foot pad fits over the leveling leg on your washing machine. The foot pad is designed to protect your floor and keep the washing machine level and in place....

$19.19

Lid Switch

This 3 prong lid switch is used for washing machines that do not have a tub light.

$22.81

Damper Pad Kit

This damper pad kit is used for base support. It comes with three six inch damper pads, two little tubes of lubricant. NOTE: This part will need adhesive to stick it in place.

$3.02

Hose Clamp

This hose clamp is used in a wide variety of household appliances. Most often it is found in washers, dishwashers, refrigerators, freezers, dehumidifiers, garbage disposals, or air conditioners. This clamp is used to securely attach a hose to another part of your appliance, which helps prevent leaks from those connections. Depending on the appliance, it can attach hoses to drain pumps, water inlet valves, pressure switches, and injector nozzles. We recommend you refer to model-specific diagrams for appropriate uses and exact placement. This hose clamp is made of metal, and is sold individually. To access and replace this part you will need a nut driver, pliers, and screwdrivers. Before you begin any repair work, make sure you have unplugged your appliance, and shut off the water supply if applicable.

$7.86

Adjustable Levelling Leg

If your washer shakes or vibrates loudly when it reaches its max speed, make sure the 4 levelling legs are even. Adjust the legs so that the machine is level, and tighten the locki...

$20.62

Lid Check Switch

This lid switch check is used in washers to detect if the washer lid is open or closed. This prevents a cycle from spinning when the lid is still open and is also used to start your washer once a certain water level is reached. If your washer will not start, agitate, drain, or fill with water, replacing the switch can be a solution to the problem. As a safety precaution, remember to unplug your washer from the power source before beginning this installation project. Refer to the manual provided by the manufacturer for further installation instructions and accurate guidance.

$19.61

Outer Tub to Pump Hose

This hose connects the outer tub to the pump of your washing machine. It is twelve inches long and all black in color. This hose is made entirely of rubber.

$5.05

Washing Machine Lid Hinge Ball

This washing machine lid hinge ball is well under an inch in diameter. These hinge balls are sold separately, though two are required per lid. This lid hinge ball is made of plastic and is used for Maytag brand washing machines.

All Parts for the A26CAE
1-14 of 221