A23CDL Maytag Washer - Instructions

Repair went well, but my switch only had one contact on the non common end. The new switch had two contacts. One is for operation with lid open and one for lid closed. Make sure to connect to the lid closed contact and the common on the other end and leave the lid open contact unused.

followed instructions elsewhere here. Procedure went flawlessly
To undo the nut I used a 1 1/2 " long x 5/16 bolt to hammer on.

STILL LEAKS. Needed PS2347235 =Tub Bearing Kit . Going back in...
THe remainder concerns the bearing procedure:
The 3 bolts holding the outer tub to the legs have rectangular washers. Those are not totally flat, and are marked for outside, top ... so pay attention. It might make a difference.
Outer tub came off the rubber bushing. Took some pulling the bushing off the shaft, and removing the sleeve bearing was a challenge at first, it would not move on the transmission shaft. Soaked with wd40 overnight. Drove it off with cold chisel (driving upward). For re-attaching the 3 tub bolts I used a ratchet tiedown strap to pull the 3 legs together to get enough thread to start, what with all those washers and things.
Ran spin cycle dry for 3 minutes as per instructions before filling with water. Success.

Your website is wonderful. I read another womans account of how she fixed her machine and then I just followed her instructions...how cool is that!

This was an easy repair.
1st I removed both water hoses
2nd I removed 1 hex head screw that released a backing plate & removed the plate holding the water inlet valve.
3rd I pulled the 4 electrical connections & loosened a clamp to remove a small water hose.
4th I removed 2 hex head screws that held the water valve to the backing plate.
-----------that was a whole 5 - 10 minutes!------------
Next I reversed the process
4th I attached the inlet valve with the 2 hex head screws
5th re-attached the 4 electrical connections(had slip on spades) pushed on the hose & tighterned the clamp.
6th replaced the backing plate with the inlet valve attached & tightened the single hex head screw.
7th re-attached the hot & cold lines................................DONE
15 minutes tops

This was a Maytag A490 of indeterminate age. Unscrewed 2 lower screws holding on front cover, removed cover. Used socket wrench to remove 2 screws holding top cover down, lifted top cover, removed old injector, replaced. The new injector didn't exactly match the shape of the old one and the lid wouldn't close. So I had to cut off some of the plastic shroud that came on the new one (didn't cut easily but I used a utility knife - BE CAREFUL). Afterwards, went in smoothly.

I started by unplugging the washing machine from the wall outlet. I then proceded to remove four screws from the top of the control panel. After removing the screws I put two flat head screwdrivers on each side of the lid and applied force to pry the lid from the ball joints holding it in place. This was the part that was the most difficult in my opinion. After the lid was off, I removed the bolt that was holding the fuse switch in place and removed that from the slots. Next I unscrewed the two screws on opposite sides of the switch head where it makes the contact with the lid. This allows you to remove the switch assembly out of the unit. Once the assembly was out, I assembled pieced the new parts together by looking at the old parts. Then, I placed the new assembly back in the unit. Be careful when you put in the new assembly that you test the switch and make sure you hear the "Click" from the switch. After that I reversed all the steps and put the unit back together.

Thirty year old Maytag washer. Remove two screws at bottom of front panel with Philips screw driver. Hinge panel up to disconnect front panel from top of machine. Tilt washer back against wall to gain access to pulley at underside of washer. Then remove Philips head screw from bottom of center shaft. Remove bevel washer with screw. Remove stop block from end of center shaft and wind the pulley off center shaft. Clean center shaft of any debris and lightly coat with grease. Install belt on new pulley and motor, wind new pulley on center shaft. Replace stop block, washer, screw, and front cover.

It was fairly easy, start out by using a screwdriver and push down and out on the front cover and remove it. Take out the 2 small bolts that hold the top cover down to the sides and lift the top cover up and lean it back out of your way. On the bottom side of the agitator there is a small bolt that holds it down, loosen that bolt and pull the agitator out. The hardest part of the entire jod was to use a small chisel and hammer to take off the nut that holds the assembly down.Remember it has reverse threads,you have to use a chisel to back it off and use some WD40 to help remove the calsium build up that is around it. Once you get that large nut off, there is a set screw on the side of the assembly that you have to loosen up before you can take it off, it's a "star driver" head and not a allen wrench set screw.Just take your time and look at your new part and compare it with the old one and take your time and remember how you take the old part off,and you will not have any problem putting the new one on. This was the first time I ever worked on a washing machine, and by checking out the parts first and comparing everything,even someone that might not have much mechanical skills can change this out. My washer works fine and not a drop of water leaks anymore.One thing I did learn, if you change this part out and put it back together and try it out and it makes a funny sound and you smell something like its burning, you might did what I did. I thought I had it to tight, but I put the large nut on before I put the tub back on!!! The agitator was holding the tub down, but it could not spin in spin cycle.... Good luck with you repairs, you can do it.

Of couse, turn off water to machine. Remove hoses. Then had to open unit - easiest by popping spring in with flat blade in seam under lid. Screws holding valve are on back of unit at hose inlet, so simply unscrew to remove failed valve. Clamp holding hose onto valve is crimped with pliers to remove. I suggest spending the 50 cents a hardware store for new clamp, as my reattachment of existing clamp onto new value leaked. There are four electrical connectors, so remember order in which you removed them and return to same on new unit.
Reassemble in reverse (hoses, water on) and your all set.
Pretty easy: I figure it would be about $200 for service guy and part. My cost: $30 and 30 minutes

Once i figured out where it was leaking from(injector hose) it was extremely easy to fix. The best way was 2 screws on front bottom, remove the front panel. Then two bolts that held the top down, lift up and the injector hose assembly was to the left in the back. It took only about 5 min. to completely replace. An extremely easy proccess.

This happened once before and had I remembered how to get the front door off and lift the top it would have taken me less time. I actually spent more time assessing prior to ordering parts than in repairing once the parts came.

One odd thing - it only leaked when the hot water was entering (if the settings were on cold only no leak - no idea why that should be).

Anyway, this injector and the rubber housing it slides into get old and clogged or deteriorate. I ordered all the parts and replace them - but probably only needed to replace the plastic injector nozzel and the rubber sleeve it fits into.

All good now - no more leaks (until the next time!)

First I took all the screws out of the side and back cabinet, then tried to pry off the top, after breaking a couple of clips, saw that the front came off with two screws at the bottom, then removed, then two hex head screws to hold on the top, then lift top and saw that the injector was clogged and leaking out the top. If I had read the repair section first, I could have saved alot of time by not removing all the side and back screws. This would be a simple 15 minute job, if you follow the repair guide. Just cut off the clamps, stick in the injector and holder , reclamp and reassemble the washer.

-determined problem
--verify that hose not clogged, screen filters clean then swapped cold w/ hot and verified that the problem was in the hot valve.
-Moved washer to get access to hot/cold valves
--opened access panel holding valve and swapped wires between hot/cold to verify that hot did not activate when it should
--Used voltohmmeter to verify that hot water valve had open circuit.
--Obtained replacement valve, installed, reconnected water lines and verified that hot and cold water worked.

I was lucky to find a youtube video that showed every step. The hardest part was removing the front of the machine only because the screws were a little tough to access. Part replacement was quick and easy. It saved me approx $150.00

All I had to do is tilt the machine to expose the bottom and replace the belts. It was fast, easy and the machine works fine now.