Models > A120 Maytag > Instructions

A120 Jenn-Air Refrigerator - Instructions

All installation instructions for A120 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the refrigerator repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the A120
1-8 of 8
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The top would not heat,large or small eye.

  • Customer: Calvin from Merced CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 12 of 19 people found this instruction helpful
Removed the bottom cover and replaced the burned contact spade. Cleaned the wires and adjust the contact holder.

one side of cooktop did not work

  • Customer: Rebecca from Broadway NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

cook top module would not heat.

  • Customer: Daryl from Olathe KS
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 5 people found this instruction helpful
The contact spades were burned from 10+ years of use and the cook top module was worn. I disassembled the module, taped the top to protect the creamic cook top, sanded the metal and spray painted to restore the original white finish. On the bottom half I replaced one missing pop rivet and cleaned and spray painted the bottom to restore to the original black. When the contact spades arrived, I replaced the contact spades and reassembled the module. It now works and looks like it did when it was new.

Glass cracked from age, over 27 years

  • Customer: RON from SAN JOSE CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Remove modular element from cooktop,place upright on bench and remove sheet metal screws. Lift glass/rim subassembly from modular heating unit (screwdriver may be required to carefully pry glass/rim assembly from heating unit) as it may be a tight fit. Inspect exposed heating unit for any noticeable damage, clean any debris resulting from cooking spills, etc. Use caution in cleaning area around heating elements so as to not damage insulation. Install new glass/rim assembly using original screws. Do not overtighten screws as this may distort the sheet metal assemblies. Install in cooktop and test for proper function.

I spilled a pot of soup and shorted everything out had to replace these parts

  • Customer: William from York PA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 4 of 7 people found this instruction helpful
Pulled out the burners, Freed the outside rim and removed the burnerbox with the burnned out pieces removed tham and reassembled

cracked glass top

  • Customer: James from Thibodaux LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 7 people found this instruction helpful
removed the damaged assembly by just pulling out from the connector. removed the broken glass top by taking out the screws holding the rim assembly and replaced the broken unit with the new one and plugged it back into the power assembly. Took all of 15 minutes.

Old Jenn--Air cook top inop. Model discontinued

  • Customer: Ronald from Avon CO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 3 people found this instruction helpful
Our Jenn-Air cook top is 25 years old. One can no longer order parts for this old of model. We ordered new SS burners as well as new Burner cartridge terminal blocks for a new and current model. They work perfectly. Took 10 minutes. $ 350 dollars verses $ 2600 for a new JennAir range plus instillation. Unit looks and works great. Plan to order new switches next.

burner cartridge terminal broke due to electrical shock. circuit shortage caused the problem.

  • Customer: Ge from Solon OH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
dissembled the burner, remove the broken blocpk and bad spade.rewiered and assembled the burner.
All Instructions for the A120
1-8 of 8