Models > A107S > Instructions

A107S Maytag Washer - Instructions

All installation instructions for A107S parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the A107S
346-357 of 357
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Leaking at base of tub/shaft

  • Customer: Bruce from Maryland Heights MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
I tried to get an appointment with our local appliance repair company, but they cancelled and wouldn't reschedule at a convenient time, so I decided to do it myself. Determined that the Mounting Stem/Tub Seal kit was the needed part and ordered it here. Also had to order the specialty spanner wrench from another website. Parts were delivered in a timely manner. The online video was very helpful and the removal and replacement of the defective part went smoothly. The only problem with the actual repair was with removing the old tub seal gasket -- it took quite a bit of coaxing to get it free. The new parts went in with no problems. However, we have an older model than the one shown in the video -- it has the metal tub top cover with the rubber gasket and ring clamp. This cover is tricky to replace properly. It has to be at just the right height to avoid interference with the spinning inner tub (too low) or with the washer lid (too high). You also have to make sure that the rubber gasket it not twisted or crimped by the ring clamp. It took me three tries to get this just right. After that, everything worked fine and the leak is fixed.

Nylon housing, brass hose coupling.

  • Customer: Richard from Lafayette Hill PA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
Be very, very careful not to cross thread the filler hose, onto the nylon valve housing. Recommend some lubrication, and a pair of velvet gloves.

During cycle, washer stopped and was smoking.

  • Customer: BRUNA from VENTURA CA
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
A friend said the cause was probably a belt. On Google we checked the washer model number which took us to your site. We looked at the videos on how to do the repairs, and so ordered a drive belt and pump belt. They arrived in two days. My husband is 84-years-old, I'm 83 -- difficult for us to lift the machine to tilt it. Experimenting with fulcrum and lever, we managed -- that's what took so long. After watching the videos again, I laid on the floor and was able to apply the belts. Washer works great!

The washer leaked out of the back left seam when filling.

  • Customer: David from Burlingame CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video on how to open this model washer. Unplug the unit. Remove the front panel. remove the bolts so you can lift the top. Disconnect the bleach tube at the top. Lift the top and hold in place with a stick or broom handle. Locate the air gap unit on filler tube. Unscrew the hose clamp on the inlet side of the air gap. Disconnect the hose and pull out the rubber tube. Fold the edges of the rubber valve off the inner nozzle and remove. Install the nozzle into the new Rubber valve. Reverse process to finish.

The washer machine would fill with water but the timer would not advance

  • Customer: Abdullah from VALLEY CENTER KS
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I hastily (miss diagnosed) the symptoms by assuming that the Drain Pump was in fault, Ordered the Drain Pump part online on Sunday got it early on Wednesday. Installed the Drain Pump but the timer would not move. So back to drawing board. Got on the phone with the nice people on PartSelect ordered the Lid Switch Assembly. Got the part in less than 20 hours To install the Lid Switch assembly remove the back panel by removing 3 sheet metal screws at the top and 2 at the bottom now you will have access to all the wires and the Lid Switch Assembly. It is attached with one sheet metal screw. The hole in the Assembly is slotted so you may have to slide it back and forth for the switch to get activated when you open the door. Installed the part, plugged the washer machine in filled the tank. The washer machine came alive the timer was moving (the washer machine start working again). This washer machine should be good for another 20 years. By the way this was the first breakdown on this washer machine after 20 years of service. Thanks PartSelect for well trained people and prompt service I couldn't have done it with out your help.

The water inlet valve was leaking water into the tub - slowly filling it up

  • Customer: John from Cedar Park TX
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
After disconnecting the power and removing the input hose connections I was able to remove the valve assembly through the back panel. I then removed the wires from the valve and disconnected the outlet hose. I removed the old valve and replaced it with the new one. Then reattached the outlet hose and 4 wires to the new valve. The assembly then was reinserted into to the back panel and screwed into place. Reconnect the input hoses and plug it in and it's ready to be tested for leaks & used. (I had no leaks, BTW. A little silicone grease on the fittings made reassembly go easier but it's not needed. )

Washtub overflowing

  • Customer: John from Fallston MD
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
Removed access panel on back of machine to remove Air Tube where it connects to wash basin. Removed control panel cover on top of machine and front panel of machine so top could be lifted for easier access to the point where Air Tube plugs in to water level selector switch. Tube is attached at both ends via spring clips. Replaced tube; problem solved. As a note, the old tube was clogged, and once cleaned, the machine functioned normally again. I had already ordered the replacement so I installed it in place of the old tube when it arrived. The new tube is significantly longer but functions perfectly.

Water was leaking out of the machine, and onto the floor during the fill part of cycle

  • Customer: Louis from Allen Park MI
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I got all of my repair information from your website. I started with 'Maytag washer leaks' and found out that, statistically, the rubber injector valve was the first most likely leak source. Then, to check if this was actually the leak, I lifted the top of the machine during the fill cycle, and watched the water spritzing from the housing that enclosed the Rubber Injector Valve. Next, I watched one of your repair videos associated with replacing the valve. Next, I ordered the part from you. When it came, I installed it. The whole process, from beginning to end, was very good.

it was a breeze

  • Customer: Mark from Cincinnati OH
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Everything basically went as planned. Putting the belts on was a breeze, but I had trouble getting on the screws that anchored the pump in. The pulley didn't allow access for a nut driver or socket, even with a universal, there still wasn't enough clearance. I went back and forth between using a screw driver in the end of a socket and using the socket on the end of a tiny breaker bar. It wasn't bad, just took a little patience. Everything works like a champ now.

Washer sometimes filled while power was off.

  • Customer: Ronald from Yorktown VA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Same technique as the PartSelect video, except the result leaked to the outside at the outlet port because the two halves of the mold that made it were slightly misaligned, and there were two steps, one on each side of the fitting. Filed the steps away, and used Evinrude gasket sealant to make sure it wouldn't leak, and it didn't.

Cold water coming into washer VERY, VERY slowly

  • Customer: Grace from New Auburn WI
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
My husband did the repair. Since he owned a laundry quite a few years ago, he knew what he was doing. After hooking everything back up, the cold water was coming in hot. When hooking up the hoses, he had hooked the cold into the top intake. After watching the online video, he realized that the plate that was to be installed over the hoses, on the back of the washer, clearly stated "H" on top and "C" on the bottom. So we switched the position of the hoses and everything ran perfectly after that. I would suggest to ANYONE doing this repair, to watch the online video first, before starting, because it is very, very helpful.

Agitator did not run properly so clothes did not roll

  • Customer: gary from king city CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Watched your viedo, pulled the power plug, pulled the washer away from the wall and tilted back to expose the belts. Rolled the old belts off and put the new ones on. Just be sure to put the correct belt on the pump and agitator drive as they are a bit different. Adjusted the pump belt as described in the inclosed instructions. What was strange was the same instructions was enclosed with the aggiator drive belt which appears to not be adjustable. Once adjusted put washer back in normal position, plugged in power and was ready to go. Seems to work fine now, least no complaints from the wife.
All Instructions for the A107S
346-357 of 357