Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A102S > Instructions

A102S Maytag Washer - Instructions

All installation instructions for A102S parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the A102S
46-60 of 162
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

washer was leaking when water level got about 4 inches in tub

  • Customer: Brian from Bush, LA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 6 of 6 people found this instruction helpful
It was fairly easy, start out by using a screwdriver and push down and out on the front cover and remove it. Take out the 2 small bolts that hold the top cover down to the sides and lift the top cover up and lean it back out of your way. On the bottom side of the agitator there is a small bolt that holds it down, loosen that bolt and pull the agitator out. The hardest part of the entire jod was to use a small chisel and hammer to take off the nut that holds the assembly down.Remember it has reverse threads,you have to use a chisel to back it off and use some WD40 to help remove the calsium build up that is around it. Once you get that large nut off, there is a set screw on the side of the assembly that you have to loosen up before you can take it off, it's a "star driver" head and not a allen wrench set screw.Just take your time and look at your new part and compare it with the old one and take your time and remember how you take the old part off,and you will not have any problem putting the new one on. This was the first time I ever worked on a washing machine, and by checking out the parts first and comparing everything,even someone that might not have much mechanical skills can change this out. My washer works fine and not a drop of water leaks anymore.One thing I did learn, if you change this part out and put it back together and try it out and it makes a funny sound and you smell something like its burning, you might did what I did. I thought I had it to tight, but I put the large nut on before I put the tub back on!!! The agitator was holding the tub down, but it could not spin in spin cycle.... Good luck with you repairs, you can do it.

Washing machine lid hinge balls fell off machine lid

  • Customer: Sandra L from Warren, OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 6 of 7 people found this instruction helpful
First I had to hold the balls into the little holes on the side of the lid - one at a time- and tap the plastic ball into the side with a small hammer. I did the same with the other side. Silde the lid to match the holes located on the washing machine - give a little push to make sure that the balls are in place. You have your lid fixed to your machine where you can lift the lid and it will stay up without falling.

Note: If the balls fall out - make sure to tap a little harder so that the balls stay in place.

Washer Leaked Water From Bottom Seal

  • Customer: JACLYN from RICE LAKE, WI
  • Difficulty: Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 6 of 7 people found this instruction helpful
Removed washer tubs inner and outer nut (part # 10 ) on inner was hard to remove and is a reverse thread used hammer to loosen once off removed 1st tub - then removed set screw #17 and then unscrewed mounting s item #29 this again required some hammer tapping to loosen - once off used flat head screwdriver to pry & remove the rubber piece on bottom of outer or 2nd tub -but keep going as the leak will probably be from part #20 tub bearing ( this will save you the time to test and find out it still leaks and have to take apart again after only replacing #29 removed 3 bolts holding tub - disconnected hoses and removed 2nd tub - used rubber hammer to knock out and install #20 tub bearing - reasembled and wow no leaks to cost about $120 - time worked on 3 hrs - only because took apart 2 times - down time on washer 10 days as we didn't order all parts to start with no beer needed but did enjoy a nice red wine - good luck

Repairs Were Easy.

  • Customer: James from Ventura, CA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 11 of 23 people found this instruction helpful
Removed top. Removed agitator and tubs . Replaced seals and reassembled.

Broken Belts

  • Customer: tommy from cortlandt manor, NY
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 8 of 7 people found this instruction helpful
Lets just say thank god for part select!!!! # 1 By far. This was a one two three job.

A chirping sound or squeak during the wash cycle.

  • Customer: Jim from WI, WI
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 8 people found this instruction helpful
I used a 1/4 inch socket to remove the agitator.Used a small screw driver to remove clip. Then I lifted the washer off the shaft with a magnet. Pried out the old seal with a screwdriver. This exposes the top of the tub bearing. I applied some 80-90 differential grease to the top of the bearing, pressed in new seal, installed other parts and noise gone. It sounds like a new washer. I'm glad I found you guys.

Standing water in washer tub

  • Customer: James from Baton Rouge, LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 5 of 6 people found this instruction helpful
Thinking the water pump was not doing its job in removing all of the water after the rinse cycle, I replaced the water pump.

1. Unplug washing machine.
2. Remove front cover (2 screws).
3. Pull belt and hoses off pump body (watch for water in drain hose!).
4. Remove 3 screws holding pump to bottom pan. 5. Reverse process with new pump.

This job is straighforward, and it helps to have 2 wood blocks to prop up the front of the washer.

Unfortunately, this didn't fix my problem. Actual cause of the water in the tub was a leaking inlet valve (solenoid assy).

broken belt

  • Customer: Ray from Cool, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 3 people found this instruction helpful
Layed the machine on it'sback and put the 2 belts on the pulleys,Very easy ,when you know to put the machine on it's backside!

pump and drive belt was thorn

  • Customer: Henry from KITTERY, ME
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 3 people found this instruction helpful
Installed drive and pump belt.. very very simple. only tool required was a screw drive to remove front panel of the washing machine.

burning smell from washer

  • Customer: kevin from mundelein, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 3 people found this instruction helpful
Replaced both the drive belt and pump belt in less than 10 minutes. Maytag has the easiest machines to work on.

slow leak at bottom of unit.

  • Customer: alex from ogden, UT
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver
  • 3 of 4 people found this instruction helpful
This job turned out to be alot easier than I thought thanks to the tips I received on the web site. First I removed the agitator with a small nut drive I believe it was 1/4". Than I removed the two screws holding on the lid and lofted it out of the way. This is where the Hammer drill comes in. I had read someone else had used WD40 to help break free the threads and get the retaining ring off the tub it self. I worked on this for about 20 minutes with lube and trying to tap it off with the hammer and tap method. Finally I looked over and sitting there on the self next to the washer was my hammer drill. It can't be any worse than banging on the thing with the hammer. (They proably don't reccomend) but with a straight tip and a couple of quick shots the gaint nut came right off. I will say that my washer being older I could barely even tell where the threads were so I figured why not. It worked great. I then took the tub ring(plastic) at the top off and removed tub. Again a couple of quick shots with the hammer drill and the ring came right off. I did spend a little time making sure everything was clean and then reassembled machine with no more leaks. It may sound strange but it worked great with no fighting the space constraints, the calcium buildup and no damage to machine. If it doesn't work get a bigger hammer. Good luck

All water into tub leaked from bottom of machine

  • Customer: Steve from Martinsville, IN
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 4 people found this instruction helpful
To troubleshoot the problem I removed a panel/blank from the back of the machine. I then started to fill the tub while watching the pump. It immediately leaked from the shaft seal. I ordered the part early the next morning. It arrived late the next day. I was able to remove the front panel of the machine by removing a screw at each front corner of the bottom of the machine. The pump was attached with three screws which were simple to remove. The pump was an exact replacement and fit identically to the original. I tensioned the belt, and tested the machine. Before reinstalling the front cover, I cleaned the interior of the machine a bit and replaced a couple of hose clamps whose steel screws had started to corrode. All in all a simple repair.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach, FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 9 of 22 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

Water leaking when washing machine was filling

  • Customer: marc from vancouver, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench (Adjustable)
  • 2 of 2 people found this instruction helpful
After ruling out leaks in the hoses, pumps, tanks, and other connections, I set the machine to start filling while I had the top open. Immediately, it was obvious the water was coming out from the injector valve (located at the top of the machine, between the water inlet mixing valve and the washing tank).

After taking this part off and disassembling, I realized that the neoprene inner part was not salvageable. (I tried cleaning off the accumulated scale and reassembling, but the rubber was too old and stiff, and no longer worked as designed.)

I considered just replacing the valve assembly, but when I saw that the price to purchase hoses as well was only slightly more, I decided to go ahead and do the full job.

The actual repair consisted of removing a couple hose clamps, sliding the new parts into place, and putting the covers back on the machine. Less than 1/2 hour.

There are two phillips head screws near the bottom of the front cover panel to remove, then two hex head screws up near the top of the machine (inside) to release the top cover from the frame. The top then tips up to reveal the inlet hoses.

At that point, the rest of the procedure is obvious. Remove the hose clamps and pull off the old hoses; install the new parts; replace the covers on washing machine.

Don't force anything into place. If you have to push that hard, chances are something is not in the right position. There is plenty of room for the parts if they are installed correctly.

Hint: use a drop of liquid hand soap to lubricate the inside of the hoses prior to pushing them onto the fittings. It makes them slide right on and saves a lot of frustration. Any excess soap will flush through on the first load and become part of the wash cycle.

water leaking

  • Customer: Stacey from Philadelphia, PA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 2 people found this instruction helpful
opened washer removed old damaged part and replaced with new part, losen brackets from hose inlet, removed hose, then fit new hose into tub groves can be very frustrating take your time and be patient, once you get it on, fit over inlet, tighten brackets make sure that seal is secure by turning on the water to fill if no leak the job is done run thru complete cycle to test. Thanks
All Instructions for the A102S
46-60 of 162