A100S Maytag Washer - Instructions

After removing the front cover and draining the tub, I replaced the drain pump and the washer works as good as new.

I turned the washer over and slipped off the old belt and then slipped on the new. The motor was spring loaded making the pepair extremely easy requiring no tools.

I have many years in maintenance and repair of ships of the US Navy. I therefore am appreciative of how you guys put this together. I received the belts on next day delivery and the video made it extarordinarly easy. Nice going. Well put together. Robert, American Canyon, CA

Follow the instruction from Partselect video. Strongly suggest to get all the tools ready, before you start.

Purchased x4 new adjustable legs. Leaned the washer back and held in place with block of wood. Loosened the two older front legs with an adjustable wrench because they had a locking nut and replaced with new legs. Repeated process on back side of washer. Once all the new legs were installed leveled the machine adjusting the legs if necessary.

First of all I had water in the machine that I had to bail out before I could tilt it back in order to work on the motor trolley, which is where the tension springs are located. I thought that the pump was not working because the tension springs that held the motor trolley back to ensure tension on the tub belt & the pump belt, were not strong enough. However, when I got the tension springs in, they were not any stronger than the springs I had. So, then I thought the only thing left to do was order a new pump belt, which I have already done. If that doesn't work, then I don't have any idea what will. I might try taking the belt I have to Auto Zone & seeing if they have one slightly smaller...beyond that, I don't know. If either the tub belt or pump belt is too tight, then one may cancel out the effectiveness of the other...very precarious. Hope this might help someone else.

1. Removed the front panel from the washing machine. This entailed removing two phillips head screws on the bottom left and right of the panel. Then, I pulled the bottom of the panel out and up until the top of the panel was disengaged from the machine. 2. Noted the belt tension on the old pump so I could install the new one correctly with the same tension. 3. Removed the two hoses from the pump, and the three screws securing the pump to the washer. 4. Installed the new pump providing the belt the same tension as I observed on the old pump. 5. Installed the hoses and tightened the hose clamps. 6. Reistalled the front panel and ran the washer. Works fine!

purchased repair kit and followed video instructions. i got the job done, without purchasing the spanner wrench. i used a punch and hammer instead. also replaced the pump and belt since these are comon wear items, and my unit is 15 years old. works like new again !

I removed the agitator, retainer nut, inner bin, old seal, and outer tub. To me it was important to clean all perts thoroughly for which I used an SOS pad and scraper which probably took me a little longer than average but I thought it was worth it to prevent doing this job all over again. Then I reversed the process.I do not have the special spanner wrench so I used a hammer and punch tool to loosen and tighten the seal and retainer nut. I also bypassed the injector valve since it was leaking as well and my washer is working fine.

Unplugged washer from power source. Disconnected hose lines. Moved washer forward and tilted. Loosened 3 screws with nut driver and removed belt. Installed new belt per instructions. Adjusted belt tension and tightened 3 screws.Connected hoses. Moved washer back and plugged it in to the electrical outlet. It all went well as long as I don't get the wrong charge on my debit card. Thank you

Pump was eazy to replace the clean up took longer than the fix.

Got ipad and follow direccions on utube.

The water pulley wheel kept seperating from the pulley shaft after numberous attempts with plumbers glue, the problem kept repeating therefor replacement was necessary. After ordering the part it was able to be replaced with the new pump and fast, washer running like new. Thank you so much.

I wached the six min. Video you sent me,so helpful what a great idea so the job only took me about five min. Thanks Mike

I took the front panel off and was able to easily access and remove the leaking drain pump. Then I propped the front of the washer up onto some boards so that I could put the two pulleys back onto the new pump, then I just tightened the three bolts in order to tighten the pulleys. However,when I started another load of wash there was a leak in the bottom of the tub, so I removed the new pump and went out and bought a new washer, figuring that our 13-year-old Maytag was going to cost more to fix than to buy a new washer. Then I wrapped up the new pump and sent it back. Thanks for all your help and for letting me send back the new part...I received confirmation of my refund today. Bob Trautman