Quick Question!

Have you ever purchased from PartSelect.com before?

Models > A100S

A100S Maytag - Overview

Parts and Repair Help for models starting with A100S

If you know the repair part you need, you can browse the list of all parts for models starting with A100S, or you can search by name or part description. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your . We’ve also included any installation videos we have for A100S parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Models starting with A100S

Exact Part matches for your search term

[Viewing 1 of 1]
$225.00

Stainless Coil Element Cartridge

This part number matches the current model number "A100S".

This part has an end plug in.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$8.90

Surface Burner Receptacle Kit

This kit comes with one ceramic block, metal bracket, wires, and hi-temp wire nuts.

Order within the next 7 hrs and your part ships today!
$8.25

Drip Bowl - Chrome - 8"

Sold individually.

Order within the next 7 hrs and your part ships today!
$6.48

Drip Bowl - 6"

Sold individually. This part is located beneath the element and catches any spills.

Order within the next 7 hrs and your part ships today!
$50.48

Mounting Stem/Tub Seal Kit

This kit comes with hub assembly, agitator seal and spanner nut. If your washer leaks once full (with or without clothes in it) or leaks during agitation, then you should replace the seal.

Order within the next 7 hrs and your part ships today!
$10.08

Adjustable Levelling Leg

Sold Individually. This adjustable leveling leg comes with a stop nut.

Order within the next 7 hrs and your part ships today!
$48.36

Tub Bearing Kit

This kit is used on 2-belt washers. It is recommended to change the seal kit at the same time.

Order within the next 7 hrs and your part ships today!
$7.79

Cartridge Male Contact Spade

This cartridge assembly male contact spade is made of metal. These are sold individually, though each range uses four contact spades.

Order within the next 7 hrs and your part ships today!
$23.74

Glide and Spring Kit

This glide and spring kit contains two three inch springs, four one inch square glides, and two tubes springs. This kit replaces older style round roller glides.

Order within the next 7 hrs and your part ships today!
$5.15

Tension Springs -Set of 2

This is a set of 2 tension springs.

Order within the next 7 hrs and your part ships today!
$125.64

Drive Motor - One Speed - 120V

Order within the next 7 hrs and your part ships today!
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

water leaking from around center shaft below fixed tub

  • Customer: douglas from bonita springs, FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Socket set
  • 401 of 411 people found this instruction helpful
My washer is 5 years old and water began to leak on the floor. I took off the front panel and filled the tub. Water did not leak immediately, but after the tub filled with about 3-4 inches of water, the water began to leak from a rubber washer between the fixed tub and the drive shaft. I looked online for exploded diagrams of Maytag washers, when I came a... read more

Drum would not drain and there was a banging noise when the drum spun

  • Customer: Charles from Whitman, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 220 of 115 people found this instruction helpful
I removed the 2 phillips screws on the bottom of the front panel. Then checked around to find the belts were actually below the floor panel.
I pulled the washing machine away from the wall and tilted it bacwards and found the pump belt was off the pully and the drive belt was badly damaged. I replaced the 2 belts which took no tools and about 3 minutes ... read more

Stove top element not working due to bad receptacle.

  • Customer: Richard from Carthage, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 136 of 147 people found this instruction helpful
Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to... read more