A100B-C Jenn-Air Cooktop - Instructions

Turned off the power at the breaker box, cut the wires approximately 5 inches from the bad receptacle and removed it after removing one screw. Stripped back the wires about 1/2 inch and attached the new wires with the ceramic wire nuts provided and secured the receptacle back in place with the new screw provided in the kit.
My sister's husband wanted to scrap the whole range but I repaired it with $14.00 worth of parts.
The element is working great now.
Whenever I need appliance parts again I'll use partselect.com.

Removed the bottom cover and replaced the burned contact spade. Cleaned the wires and adjust the contact holder.

Our Jenn-Air cook top is 25 years old. One can no longer order parts for this old of model. We ordered new SS burners as well as new Burner cartridge terminal blocks for a new and current model. They work perfectly. Took 10 minutes. $ 350 dollars verses $ 2600 for a new JennAir range plus instillation. Unit looks and works great. Plan to order new switches next.

Replaced receptacle but it was not the problem. After further inspection I believe that the problem is the switch. The switch is on order now from Part Select.

I have bought several drip bowls over the years. They all seemed to not fit just right. These are perfect! Thanks!

Worst part of the job was removing the old screws that held the two old rectecles in place for the two burners I repaired. Once the screws were removed cut the wires stripped them and used the porceliean wire nuts provided with the kit. Easy job and good instructions.

I took out the side of the cooktop that did not work. I had to take off the bottom of the cooktop and checked where electricity was going and not going. Once I found the part that needed replacing, I went on the website, search for Jen-Air cooktops and model number. From the sketch on the website, I was able to order the part needed. I decided to get 2 in order to replace both parts at one time, just in case. The part arrived quickly and was easy to install. The most time I spent was taking the backside off the cooktop and cleaning it.

The contact spades were burned from 10+ years of use and the cook top module was worn. I disassembled the module, taped the top to protect the creamic cook top, sanded the metal and spray painted to restore the original white finish. On the bottom half I replaced one missing pop rivet and cleaned and spray painted the bottom to restore to the original black. When the contact spades arrived, I replaced the contact spades and reassembled the module. It now works and looks like it did when it was new.

Problem was the neutral connector spike was burned and didn’t make good connection. Service man said he couldn’t get parts and charged $100 and left.
The neutral conductor cost about $12. And was an easy fix!

Thank you PartSelect!

Changing the socket with a new one simply required removing one screw and splicing the two existing wires to the pigtails on the new socket. It took longer to unpack the replacement part than actually doing the job.

First I removed a screw that held the element in place then disconnected the two wires . Then I just reattached the two wires put the screw back in place and was done in about 10 minutes. Fairly easy fix, I had this go out a few years ago and had a repairman fix it, and saw how easy it was, so this time I did it myself. Easy job!!

Pulled out the burners, Freed the outside rim and removed the burnerbox with the burnned out pieces removed tham and reassembled

Our stove is from 1978 and was missing all but one drip bowl. I bought all the replacement parts from all the store, (Walmart, Target, Fred Meyer) nothing fit. I finally found this site and they fit perfectly! Thank you. If I have to keep the stove a while longer at least it looks clean and new now, and it still works great!

remove cartridge unit from cooktop, remove 7 small bolts and 2 screws and remove cover. install new cover and replace hardware that was removed and install back in to the cooktop.

1. Shut the breaker off; Jenn-Air's design will have you working around hot leads if you don't.
2. Raise the control panel
3. Remove burner and unscrew the burner connector; trace the wires back to the control panel bottom and remove them
4. On the replacement connector, add the electrical for the control panel. These are not included and can be found at any hardware store; they are a standard size.
5. Connect the new wires and put everything back together.
6. Reset the break and test.