Models > 9815VUV > Instructions

9815VUV Magic Chef Wall Oven - Instructions

All installation instructions for 9815VUV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the wall oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9815VUV
46-60 of 137
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

The old light switch was broken

  • Customer: James from Charleston, AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
The replacement switch was slightly larger than the old one so it would not go through the hole in the front panel so I had to get a reaming tool and enlarge the hole just a little for the switch to go through. It was still an easy repair as I had the proper tool.

Faulty bulb receptacle

  • Customer: Kenneth from Lynchburg, VA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 5 of 13 people found this instruction helpful
Unplugged the stove and removed the back panel, disconnected the wires from the old receptacle, removed it, inserted the new receptacle, connected the wires, put the back panel of the stove on, plugged in the stove and then checked to see if the bulb was now burning. Success!

oven not heating to set temp. 100 degrees too cold

  • Customer: Robert from Funston, GA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
installed part,turned unit on-temp still cold. reset digital control, up 35 degrees, still cold. un-plugged unit,re-connect after 10 min. still cold.

Oven not heating to desired temp

  • Customer: Raymond from Ridgecrest, CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 5 people found this instruction helpful
Had to remove oven from mounting cabinet to get to the back since the wire lenght to the conector was to short to come through the mounting hole.
Other than that the repair was straight forward. 4 screws to dismount the Oven from cabinet, 2 screws to remove Sensor and 3 srews to open the back of the oven once out in the open. New cable adapter that came with the new sensor was needed in my case.

burned out element

  • Customer: Richard from Highland Village, TX
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
This was an easy thing to do. Take the two screws off the back, pull the wires out, pull off the connectors, get the new element, replace the connectors, make a hole in the insulation, fish the wires back behind the insulation, screw the mounting screws and turn it on. The only thing I did extra is clean the bottom of the oven because with the element out, it's easy to do.

burned oven bulb

  • Customer: Ivanka from Atlantra, GA
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 8 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

Lower element was broken.

  • Customer: Daniel from Wilmington, DE
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Awesome, just awesome, you guys are great and I will use you again and again.

light bulb went out in my oven

  • Customer: Janet from Ada, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 5 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Heating element burned out

  • Customer: Ellis from West Valley City, UT
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Found the model number, called the local parts store, they quoted $60 + $10 shipping because it was a warehouse order or something. So I came hear and got it for $42 + $7 shipping!

Turned off power, unscrewed the element, disconnected the clips from broken element, connected them to the new, screwed in the new element, and it was done

the element was burned!

  • Customer: Terry from Arlington, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
unscrew the old ones and replaced the new one - easy as that! Savings of over $300.00 if I need to buy a new one! Thanks for the speedy service after I ordered it.

oven element not wrk'n

  • Customer: Debbie from MT.VERNON, IL
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Simply removed old element,2 screws,clean'd oven b/4 install'n new one,reconnect'd 2 wires,2 screws & yea oven wrks again. My husband was very happy as the oven is 34 yrs old,I just copied the model #,went 2 u'r web site,& we r very happy campers,so thank you very much.
Debbie A. Martin

took to long to preheat and food wasn't cooked on the bottom

  • Customer: Jessica from Lubbock, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First, I want to say that this part arrived within 24 hours of placing the order. I was plesantly suprised. My husband did the repair and it was super easy. We had no problems.

Thanks PartSelect!

F1-1 and F3-1 error code

  • Customer: Barbara from Lakeville, MA
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 5 people found this instruction helpful
Very easy to repair, but you have to be able to pull your stove out. Two screws in the oven and then remove part of back cover of oven and one plug from there. Simple to do, but did not fix our problem. We are waiting repair now from service company as it looks like it needs a control panel. Worth trying yourself to fix the problem. Inexpensive part and easy to install. Also be sure to turn power off your oven to reset the control panel as this may fix the problem - try this first and also after installing new part - like rebooting a computer...

Bake Element burned out

  • Customer: John from Lincoln Park, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Determining the correct bake element to order was the most difficult part. Once I received the part, it took me 2 minutes to unscrew the back panel, detach the wires, connect the new wires and re-connect the back pannel - turned the oven on to test - and we were all set just in time for Chistmas baking.

element burned out

  • Customer: luke from warren, OH
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
First I removed the two screws that hold the element in place. I then pulled the element out about 3 inches and disconnected the two wires, that were clipped on. slipped them off connected the new element screwed it back into the oven.
All Instructions for the 9815VUV
46-60 of 137