Models > 9122XUB > Instructions

9122XUB Magic Chef Oven - Instructions

All installation instructions for 9122XUB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9122XUB
61-75 of 202
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't heat. Igniter was broken.

  • Customer: Thomas from Allison Park PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
I removed the back of the range to disconnect the wires to the igniter. Then I removed the two screws holding the igniter, screwed the new one in and reconnected the wires in back.
I was really pleased how easy it was to find the part on the website and how quickly the part came. The whole job was a snap. Thanks!

igniter glowed, but oven would not light or stay lit

  • Customer: Daniel from Grafton WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
The igniter was located in the bottom of the stove or broiler section. It was hard to get at, but with a little trial and error I figured out how to take the plate between the oven and broiler. Now the igniter was easily accessable. 2 screws on the igniter bracket, then simply unplug the electrical. The igniter supplied had the identical electrical plug (plug and play). The new igniter works like a charm-oven ignites in about 15 seconds. Piece of cake!!!!!

Thermostat bulb was hanging loose

  • Customer: Willi from Old Saybrook CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers
  • 2 of 5 people found this instruction helpful
Removed what was left of the original clips. Pressed in the new clips and snapped in the themostat blub

IGNITER WOULD GLOW BUT STOVE WOULDN'T LIGHT

  • Customer: ALAN from LUCK WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I NOTICED THAT THE IGNITOR WOULD GLOW BUT THE STOVE WOULDN'T LIGHT - I GOT THE MODEL NUMBER OF THE STOVE AND GOOGLED THE MAYTAG MODEL NUMBER. CAME UPON YOUR WEBSITE AND REALIZED THAT 94% OF THE TIME THE PROBLEM WAS THE AMPS WERE NOT ENOUGH TO LIGHT THE STOVE. I LOOKED AT ALL OF THE STORIES ON HOW EASY IT WAS TO FIX. I ORDERED THE PART AND RECEIVED IT WITHIN 3 DAYS. I OPENED THE DOOR PART WAY AND LIFTED IT STRAIGHT UP TO REMOVE IT. I PULLED OUT THE BOTTOM BROILER PLATE BY GRABBING THE BACK ON PULLING UP. I UNDSCREWED THE WING NUT OF THE FLAME BAR AND HAD EASY ACCESS TO THE IGNITER. I REMOVED THE TWO NUTS FROM THE OLD IGNITER. UNPLUGGED THE IGNITER FROM THE EASY ACCESS DOOR FROM THE BACK AND PLUGGED IN THE NEW IGNITER. REPLACED THE ACCESS DOOR AND ATTACHED THE IGNITER WITH THE TWO NUTS. PUT THE FLAME BAR BACK ON, PUT THE BROILER PLATE BACK ON, PUT THE DOOR BACK ON, PLUGGED IN THE STOVE TURNED IT ON AND SUCCESS. IT WAS SO EASY. I KNOW IN OUR AREA I WOULD HAVE PAID NEAR $200 FOR A SERVICE TECHNICIAN TO COME OUT AND DO WHAT I DID IN APPROX. 20 MINUTES AND $50 FOR THE PART. THANK YOU SO MUCH FOR YOU WEBSITE TO HELP US NOT SO TALENTED APPLIANCE REPAIR HOMEOWNERS.

Replaced Oven/Broiler Knob

  • Customer: William from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
All I had to do was slide it on. The hard part was that I could not find the modle number anywhere, and your web site showed me possible places to look, so that I was able to find the modle and order the part that I needed.
Thanks so very much, William Millard.

Oven Ignitor went to ignitor heaven.

  • Customer: Brian from Pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 1 of 2 people found this instruction helpful
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

Oven making whooshing sound and not heating up

  • Customer: Jason from Williamsburg VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

Oven did not ignite

  • Customer: John from Racine WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

Replacement of igniter

  • Customer: Robert from Orange CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

oven in range would not stay lit or achieve temperature

  • Customer: Raymond from Jersey City NJ
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
I slide range away from wall, unplugged the electric. Lifted door off the hinges for easy access. The broiler drawer also comes right out. Removed racks and then took out bottom panel. The ignitor is mounted with two hex nut screws. They came out with a phillips head screwdriver. The plug connector is accessable from the rear or the range, there was nothing else to take off. I simply unplugged the connection, pulled the wire through the insulation, screwed on the new ignitor and pushed the plug and wire back through the insulation and plugged it in. The job took less than 25 minutes and that time included cleaning behind, under and inside the range! Oven lit first time it was turned on and works as good as new.

Strong odor of gas when oven in use. Oven took over a minute to light with low flame level (ie 1/4").

  • Customer: Linford from Cedarville NJ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Removed bottom plate from oven enclosure.
Removed the two screw holding the burner in place. Disconnected plug to element, making sure wire did not fall back into underside of oven.
Removed heating element. Replaced element & reinserted burner assembly into oven. Checked oven operation before reinstalling bottom plate. Oven ignition was less than 15 seconds with over one inch flame from burner.

Oven wouldn't ignite

  • Customer: Anatoly from Palatine IL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 1 of 3 people found this instruction helpful
1. Unplugged power cord and remove bottom oven tray.
2. Disengaged plastic connector from the back of the diverter valve.
3.Unscrewed two screws, holding present igniter.
4.Cut two wires, coming from the old igniter, with wire cutter (pliers).
5. Discarded old igniter assembly (in two parts -igniter and connector).
6. Attached connector part of new igniter to straightened coat hanger with insulation tape.
7. Fed the coat hanger from inside toward range back side by slightly displacing present oven insulation.
8. Removed coat hanger when got through.
9. Re-fastened new igniter with old screws.
10. Re-plugged plastic connector into diverter valve.
11. Re-plugged power cord and replace bottom tray.

Tested performance and am totally satisfied with the component and seller's service. There was no need for the extra materials in the kit.

Outside glass on oven door shattered.

  • Customer: April from Denham Springs LA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 3 people found this instruction helpful
Simply unscrewed the door handle and replaced the glass. Easy.

Our oven took a long time to light and come up to temperature. Very frustrating since I cook and bake a lot!

  • Customer: ALISE from LUDLOW MA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
First we removed the two screws that hold the element in place. Then detached the wire from underneath the oven. We then had to pull out the oven to access the back panel. We unscrewed the back panel and detached the second wire. Then we revearsed the process and installed the new igniter. The whole thing from start to finish took about 35min. This was very easy to do and I am happily baking once again. The whole family is happy about that :)

OVEN WAS DEAD

  • Customer: IRIS from BROOKLYN NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 1 people found this instruction helpful
This oven was purchased in 1992 . Hardest & time consuming issue was getting the old part out.
First unplug unit from outlet. Take off oven door(very easy to do). Take out oven racks & lift out bottom of oven(also simple to do). Pull out storage drawer all the way out & put aside out of your way. Take off burner baffle. This is held on with 1 butterfiy screw. This igniter plugs in the same way a phone slips into the jack. Use a flash light if needed. Where you pulled the storage drawer out from all the way in the back pull out the connection holding the old ignition wires into the oven(this is the phone type part spoke of above). Go back into the oven & un screw the 2 screws that hold in the igniter to the bake burner pipe. Now you can carefully pull out the old igniter since you already unpluged it earlier. Slip connection wires from new igniter in the same hole old was pulled from in back of oven. Screw the 2 screws into the new igniter to hold it to the bake burner pipe. Go back down to the storage draw space & plug into bottem back. Replace storage drawer. Replace burner baffle.Replace bottem of oven making sure to seat it in correctly. Replace door . Remember to connect to electric again & you should be good to go. I WOULD LIKE TO NOW SAY SOMETHING ABOUT THE EXCELLENT SERVICE RECEIVED FROM PARTS SELECT.
THEY HAVE AN EXCELLENT USER FRIENDLY SITE & I RECEIVED MY PART THE NEXT DAY.
All Instructions for the 9122XUB
61-75 of 202