Models > 9122XPB > Instructions

9122XPB Magic Chef Oven - Instructions

All installation instructions for 9122XPB parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9122XPB
46-60 of 202
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Igniter was not getting hot enough to allow burner to come on.

  • Customer: ELMER from BONNEY LAKE WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
took out two screws that held Igniter to burner, unbluged wires from behind and pulled them out to the front of over, replaced with new one, solved the problem of the burner not coming on,,,,

The old light switch was broken

  • Customer: James from Charleston AL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
The replacement switch was slightly larger than the old one so it would not go through the hole in the front panel so I had to get a reaming tool and enlarge the hole just a little for the switch to go through. It was still an easy repair as I had the proper tool.

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Replaced a broken hinge.

  • Customer: Joseph from New Windsor NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
The repair was easy. The door pulls off the hinges without any tools. I had to remove four screws ihat held the wall oven in place. I then removed approximately eight trim screws to expose the two screws holding the hinge in place.I then needed to utilize a nut driver to put the screws in the new hinges because the screws cut threads into the hinge as you put them in so they are a little tight and the nut driver makes this step easier.

Oven would not start, ignitor was not doing anything

  • Customer: Michael from Syracuse NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench set
  • 1 of 1 people found this instruction helpful
My wife said the oven would not heat up, I took a look at it and determined it was not igniting. I figured there was an electric spark like my BBQ. When I took the pan out of the bottom of the oven I saw that it did not look like anything I had seen before. I looked it up online and found out it had a glow ignitor that just heats up and then ignites the gas. Mine wasn't doing anything so I removed it, got a part number off of it an plugged that into this site. It came up with the part, i ordered it, put it in and started it up. probably took about 45 minutes total including taking it out and then replacing it. Really easy and the oven is now working fine. Figured it would have been a couple hundred dollars to have someone come to the house and fix it, I did it myself for less than 50. Thanks Partselect.

broke the igniter in the oven before I even got the oven installed

  • Customer: june from wills point TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.

oven would not light

  • Customer: gary from covington LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

Oven was not working at all

  • Customer: Glynne from Dedham MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!

Oven Ignitor went to ignitor heaven.

  • Customer: Brian from Pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 1 of 2 people found this instruction helpful
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

Replacement of igniter

  • Customer: Robert from Orange CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

Oven did not ignite

  • Customer: John from Racine WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

Oven making whooshing sound and not heating up

  • Customer: Jason from Williamsburg VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

IGNITER WOULD GLOW BUT STOVE WOULDN'T LIGHT

  • Customer: ALAN from LUCK WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I NOTICED THAT THE IGNITOR WOULD GLOW BUT THE STOVE WOULDN'T LIGHT - I GOT THE MODEL NUMBER OF THE STOVE AND GOOGLED THE MAYTAG MODEL NUMBER. CAME UPON YOUR WEBSITE AND REALIZED THAT 94% OF THE TIME THE PROBLEM WAS THE AMPS WERE NOT ENOUGH TO LIGHT THE STOVE. I LOOKED AT ALL OF THE STORIES ON HOW EASY IT WAS TO FIX. I ORDERED THE PART AND RECEIVED IT WITHIN 3 DAYS. I OPENED THE DOOR PART WAY AND LIFTED IT STRAIGHT UP TO REMOVE IT. I PULLED OUT THE BOTTOM BROILER PLATE BY GRABBING THE BACK ON PULLING UP. I UNDSCREWED THE WING NUT OF THE FLAME BAR AND HAD EASY ACCESS TO THE IGNITER. I REMOVED THE TWO NUTS FROM THE OLD IGNITER. UNPLUGGED THE IGNITER FROM THE EASY ACCESS DOOR FROM THE BACK AND PLUGGED IN THE NEW IGNITER. REPLACED THE ACCESS DOOR AND ATTACHED THE IGNITER WITH THE TWO NUTS. PUT THE FLAME BAR BACK ON, PUT THE BROILER PLATE BACK ON, PUT THE DOOR BACK ON, PLUGGED IN THE STOVE TURNED IT ON AND SUCCESS. IT WAS SO EASY. I KNOW IN OUR AREA I WOULD HAVE PAID NEAR $200 FOR A SERVICE TECHNICIAN TO COME OUT AND DO WHAT I DID IN APPROX. 20 MINUTES AND $50 FOR THE PART. THANK YOU SO MUCH FOR YOU WEBSITE TO HELP US NOT SO TALENTED APPLIANCE REPAIR HOMEOWNERS.

Replaced Oven/Broiler Knob

  • Customer: William from Santa Rosa CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
All I had to do was slide it on. The hard part was that I could not find the modle number anywhere, and your web site showed me possible places to look, so that I was able to find the modle and order the part that I needed.
Thanks so very much, William Millard.

Bottom oven burner wouldn't light.

  • Customer: James from Lino Lakes MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.
All Instructions for the 9122XPB
46-60 of 202