Models > 91195589990 > Instructions

91195589990 Kenmore Range - Instructions

All installation instructions for 91195589990 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 91195589990
1-15 of 127
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Large burner on dual element burned out

  • Customer: Scot from Oakland FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 37 of 44 people found this instruction helpful
This was really easy, and pretty with no problems or issues It took me longer to write this than to do the actual installation. I used a digital camera to help me remember where things were, but a pen/paper works fine. Here's what I did:

1. Turn off the breaker for the cooktop.

2. Remove (2) 1/4" hex screws directly under cooktop. You may need to open oven door to reveal them.

2. Prop up cooktop. I used the box the replacement element came in.

3. The element is held in place with (3) brackets held in by a #2 philips screw each. Mark the location of each of the brackets. There are numbers on the element to help you do this.

4. Write down where each of the wires connects to the element. There's only a few of them, but I tend to forget that stuff. The wires have female spade-type connectors that connect to the male ends on the element.

5. Using a needle-nose or small pliers wiggle each wire off the element. Grab the wires by the end of the female connector when you do this. I found it helpful to use a small flat screwdriver to help pry them off. Mine were on pretty tight, so expect this to take a few mins. If you have problems getting to the wires, remove the brackets (next step) first and come back to this one. I let the element hang from the wires without any problems, but I still wouldn't recommend it.

6. Remove each of the screws with a #2 philips screwdriver. Support the element with your hand and gently pull each bracket away from the element. Once they're all gone, the element should just come out. I took a look at my old element and saw that the large burner wires were melted in a couple places, so it was definitely broken.

7. If necessary, clean the underside of the cooktop surface with a clean papertowel. There was a little dust from the old element on mine.

8. Connect the new element and test to make sure it works by turning on the breaker and turning on the burner for a second or two. Note: This will make the top of the element hot for some time, so test it and go away for a few mins. If it works OK, proceed. If not, disconnect and figure out what else may be wrong.

9. Using the old element, make copies of the marks you made for the bracket locations onto the new element. You'll have to punch through the insulation when re-attaching the screws.

10. Re-wire the new element, if necessary and re-attach the brackets over the marks you made. This may be a pretty tight fit because the new element was thicker than the old on mine. I opened up the brackets a bit to make it not so hard to re-attach. Hook the brackets on and squeeze them over the element. The holes in the brackets need to line up with the holes drilled into the bottom of the element. If they don't, spin the element around (or detach and re-attach the brackets) till they do.

11. Screw in the (3) screws over the brackets pushing them through the insulation on the element.

12. Close the cooktop and reattach the hex screws under it (1/4" hex).

13. Turn on the breaker and test again.

Thats it, works great now. Good Luck

Broiler element failed

  • Customer: paul from west grove PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 29 of 32 people found this instruction helpful
repair took about 30minutes total tiem..first turn off power to stove..then open oven removed racks..used nut drive to loosen top two screw hold element..then remove screw hold temp sensor element...then removed two screws holding broiler element...then removed the top screw ...then pulled element out about 7 inches to expose wire connection..held on with spade lugs.. pulled wires off...element now free to remove ...placed spade lug on new element...put element in pace with top two screws..loosely...then did rear screw that held temp element and broiler element...then tighten all screws ..turned on power..did 15 sec test to make sure wired properly..then 5 minutes to operating temperature... job done...hardest part was crazwling in and out the stove...old bones..

Large burner would not get hot

  • Customer: Kevin from Leominster MA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 27 of 36 people found this instruction helpful
Repair was very simple. Removed 2 screws under the cooktop, tilt the cooktop back, unplug 4 wires from 8" burner, remove two screws holding retaining clips, install new burner in reverse order. Very simple!

I needed new oven racks

  • Customer: jamie from MORRISVILLE PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 23 of 26 people found this instruction helpful
My husband had turned the oven on to cook something and didn't know that I have a plastic tray in there. Well, needless to say I needed to get some new oven racks. I tried to get them through the manufacturer (GE). They were 68$ each. I thought that was a bit steep, so I looked online. I decided to order through PartsSelect. Well...they can 2 days later (the week before Christmas!!)and were a PERFECT fit.
Between the price, shipping speed and quality I will
definitely buy from again and recommend this site to everyone I know!!!!

Oh yeah, I work for Sears too. we have access to all sorts of parts....this site is the BEST for prices and delivery speed!!!!

COIL BURNED OUT

  • Customer: Frank from St Augustine FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 30 of 51 people found this instruction helpful
OPEN LID,UN SCREW COIL,POP IN NEW COIL SNAP HOLDERS IN PLACE,THEN COOK A STEAK

heating element fractured when cooking easter dinner

  • Customer: daniel from pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 17 of 20 people found this instruction helpful
removed 2 screws that mounted element. disconnected 2 wires, reconnected wires remounted the element. Done in 5 minutes.

Two part burner, outer ring not working

  • Customer: JERALD from PHENIX CITY AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 16 of 19 people found this instruction helpful
The outer ring on the adjustable large haliant surface burner of our smooth top stove would not work. It would only work on the small (inner) size.

Found the part on this site, ordered, 3 days later, and it was fixing time.

2 screws removed to lift cooktop, 2 screws to remove old burner and disconnected 4 electric clips one at a time and placed them in same position on new burner. Replace the 4 screws and done.

VERY SIMPLE.

Don't clean your oven with the racks still in, takes the finish off!!!!

  • Customer: Robert from Apison TN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 14 of 15 people found this instruction helpful
Took old racks out, slid new ones in....exact match at a huge savings from what GE wanted per rack.
Found the company through a Google search, have it bookmarked and will be back if I need something from them.

Heating element burned out.

  • Customer: LANCE from ORELAND PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 18 of 29 people found this instruction helpful
Unplugged range. Opened oven door and removed two screws from top of oven opening. Lifted oven top and propped up
with a 2 x 3.Unscrewed the two screws that were holding

Range door bottom trim got rusty: a lousy design by GE.

  • Customer: Donald from Delmar NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 13 of 15 people found this instruction helpful
I used a screwdriver and pliers. A nut driver would have been helpful. Oven door is removeable for cleaning and maintenance, but it's heavy and awkward. It has to be laid face-side down to disassemble, so have a protected tabletop ready to avoid scratches. Side trim pieces have to come off to get access to bottom trim mounting screws.

Left rear element would not get hot.

  • Customer: John from Hopewell Junction NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 12 of 17 people found this instruction helpful
FIRST TURN OFF THE CIRCUIT BREAKERS THAT POWER THE COOKTOP!! Remove the cooktop from the counter by removing the screws from the mounting straps under the counter. Then remove the screws that hold the glass cooktop to the frame and lift off the glass top. Next lift up the bad element and unplug one wire from the bad element and plug it into the new element. Make sure to put it on the exact same terminal of the new element. Do this for all the wires. Remove the two mounting tabs from the old element and put them on the new element. Turn on circuit breakers and your done.

Inner element of dual burner died

  • Customer: Van from Hyde Park NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 10 of 12 people found this instruction helpful
-Turn off breaker
-Undo the two screws that hold the top surface down
-Prop up top surface with a board
-Remove two screws/spring clips holding burner
-Transfer electrical plugs to new burner (this was the most challenging part)
-Screw new burner in place
-Lower surface
-Secure surface

Broiler Unit was burnt out

  • Customer: Brenda from LaFollette TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Wrench set
  • 8 of 9 people found this instruction helpful
First I had to remove the oven ceiling screws bracing the broiler element. Second I removed the screws holding the connectors at the back of the oven before I could disconnect the two wires ( which were awkward for me to get to because I am 5'2" but was able to reach without removing the oven door).

I reconnected the two connectors and screwed the brace into the back of the oven. Then replaced the screws into the ceiling of the oven to hold the unit in place.

I was very pleased to have been able to do this project on my own and the broiler is working fine.

defective temp. sensor

  • Customer: Armand from COVENTRY CT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 9 of 12 people found this instruction helpful
Removed oven from cabinet. unblug old sensor pluged in new and reinstalled oven. Esay repair though wish oven was designed so did not have to pull itout of cabinet which requires disconect electric cabel

Oven sensor was not holding temperature range.

  • Customer: CHARLA from NEW BRAUNFELS TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 18 of 39 people found this instruction helpful
Per the instructions included with part.
All Instructions for the 91195589990
1-15 of 127