Models > 91195402000 > Instructions

91195402000 Kenmore Range - Instructions

All installation instructions for 91195402000 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 91195402000
61-75 of 125
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Cleaned oven with shelves inside...

  • Customer: Carol from Roanoke VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 2 people found this instruction helpful
I too made the mistake of cleaning the oven with the shelves in place. It doesn't really harm them...but they turn a tarnished brown color...they look dirty. These replacement shelves were a perfect match. Pricing was reasonable, communication was terrific and shipping was super fast. Happy camper here :-)

blew into pieces.

  • Customer: Ratha from Danbury CT
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set
  • 0 of 2 people found this instruction helpful
There is not much to it!

BROKEN LIIGHT SOCKET

  • Customer: Rchard from Derry NH
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 8 people found this instruction helpful
Removed the broken socket, and replaced with new one.

Broiler Element shorted out

  • Customer: Frank from Riverbank CA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 2 people found this instruction helpful
Remove old, Installed new as per instructions.

eye wouldnt come on

  • Customer: daniel from valentines VA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 2 people found this instruction helpful
removed the top section on stove and removed the wires off swtitch and put on new one then put new switch in

burned oven bulb

  • Customer: Ivanka from Atlantra GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 2 people found this instruction helpful
The hardest part was taking out original light bulb because screws on shield where hard to unscrew after all this years . The old bulb vent out leaving neck in socket. It took narrow electrical pliers to get neck out .The generic appliance bulb did not fit and had aluminum neck ,not recommended for brass sockets in ovens.Putting new light bulb in was not the problem.

switch went to high setting no matter what the setting was

  • Customer: Frank from Glen Cove NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 3 of 12 people found this instruction helpful
took off cover, pulled all wires off switch, pushed wires on new switch, put cover back on. Whalaa..

Burner not heating.

  • Customer: Jack from Greensboro GA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 3 people found this instruction helpful
Isolated to control switch.

Replaced

temperature sensor went

  • Customer: Alex R from Randoff NJ
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Took back panel off unplugged sensor and replugged in and worked like a charm!Sears wanted $400 and was going to 'overrepair"Got the 60 dollar part on here. UPS shipped to wrong address and customer service refunded my shipping and was excellent! would definetly use again!thanks

burned out oven light

  • Customer: Herbert from Virginia Beach VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Socket set
  • 0 of 0 people found this instruction helpful
Turned off the power to the stove. Removed the oven door, Removed two screws holding the metal housing from the oven wall. pulled the assembly forward, removed the two electrical wires from the back of the socket, installed new gasket on back of metal assembly,inserted the wires thru the hole in the metal assembly, attached the wires to the new socket, pushed the new socket in place making sure the two holding clamps were in place, screwed assembly back in oven wall, replaced new bulb, replaced glass cover over bulb, Replaced oven door, turned the power back on, Light works like new.

missing oven racks

  • Customer: Casey from Charlotte NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Parts fit perfect, and order them on Wednesday and they were delivered on Friday morning. Excellent service. Thank you. Happy customer.

Oven door trim rusted (bottom of door)

  • Customer: thomas j from canal winchester OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
This repair is really easy unless the trim piece has rusted so badly that it's attached itself to the front door glass. It took a long time and some WD-40 to pry the trim off w/o breaking the glass. REPAIR: Remove the door and lay it on a flat surface. Unscrew the 3 bottom screws w/ small pliers, then unscrew the top two inside door screws w/ a small metric allen wrench. Remove the door trim to get to the last four side trim screws. Once the old trim is out just clean up any residue/rust remaining on the glass, install the new trim and reverse the steps to put the door back together. If the old trim comes off easily it should only take @ 20-30 minutes.

A large burner (haliant Burner 8" ) went out on my Hotpoint Electric Range

  • Customer: Ruth from Potosi MO
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
I ordered the part on a Monday and Tuesday afternoon I received it! I went a route I often take first. I read the instructions of others before starting my job and opened the top of the range. There are two screws under the range top in front near the oven door, one on either side, that must be removed. After this I opened the top of the range and positioned a piece of 2X2 about 20 inches long at an angle to hold the top up while I worked on the burner. I then used my phone to take a close up picture of the old burner while in place in my range so I could refer to it when putting the new one in place. I then took a pair of needle nose pliers and pulled off the wiring, then removed lock washers under the burner and removed the old burner, being careful not to lose the washers and springs. I took the new burner and layed it along side the old one to see exactly how it would be placed under the glass cover. I replace the springs and lock washers then referred to my photo and replace all the wires to the burner as they had been. Then lowered the top in place and put the screws back in place. That was it. I'm a 67 year old female, if I can do this, anyone can!

Getting the right stove model number and part number

  • Customer: Gerald from San Diego CA
  • Difficulty: Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Difficulty was in determining the right model number and part number of a switch. Noted that the left front burner came on when the switch for the left back burner was turned on. By inspection I found the left front burner switch had become faulty by actually hearing an electric arc in the switch and smelling the oder in the switch. With help from the person I called I was able to determine that the Model Number on the actual stove was wrong. It had an extra 0 between the W and F which she said was a common error in the GE model number. I then gave the switch number I found on the switch to the contact person and she was able to verify the right part number. It was relatively easy to replace the switch by taking off the back upper plate then taking off two screws that held the switch to the stove. The part came quite quickly once ordered. Sears repair wanted $75 just to diagnose then the cost of the part. I got the switch for $69.

Missing oven rack

  • Customer: Christine from Coeur d Alene ID
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
This website made it so easy for me to find the part I needed! Shipped promptly with no problems or delays and the rack fit perfectly in my oven.
All Instructions for the 91195402000
61-75 of 125