Models > 91193402992 > Instructions

91193402992 Kenmore Range - Instructions

All installation instructions for 91193402992 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 91193402992
256-270 of 273
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drip bowls were rusty and not original GE. Small burners never fit quite right and rocked unevenly.

  • Customer: Ian from Casselberry FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Ordered new parts. Received email with tracking number. Parts arrived as promised. Turned off power at breaker (!). Removed burners and pans. Lifted the lid of the range. Inspected the plugs and discovered one had come loose from bracket and was not in straight. Reset plug in bracket. While the lid was open, placed the drip bowl in opening and installed the burner and made sure the burner was laying properly in the drip bowl. Repeat for each. Perfect fit, If done properly, the small burners should lay down flat and not rock back and forth. I have seen complaints about rocking, and experienced some of it on one burner. Make sure the heating element is set in the plug well and it should work. A little patience may be required to get it just right. Everything lays flat and the stove looks new again. I have purchased from Part Select on other projects including a dryer rebuild and a new face plate for this range. Great products, reasonable prices, wonderful tutorial videos and good service.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Lower bake element not heating.

  • Customer: Frank from Oregon OH
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Pulled range out, disconnected from wall socket. Unscrewed back center cover (3-4 1/4" hex head screws). Removed slide on terminals from lower element. Used multimeter w/continuity checker and found no continuity from tab to tab. (You will get continuity if you touch the outer sleeve). Open the door to oven, remove rack for easy access, unscrew the two 1/4" hex head sheet metal screws holding element in place. Pull element out gently. Slip new back in, securing in place w/screws. Replace rack. Slip on terminals, making sure that they are completely on. Replace back cover. Plug in. Tah dah!

replace bake element

  • Customer: Philip from Hayfield MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
I unplugged the stove and removed the oven racks. Then I turned on a flashlight and laid it in the oven so I could see. Next, I carefully connected the push on terminals. Then I screwed in the two screws with a nut driver. Finally, I replaced the oven racks and plugged in the stove, and I was finished!

oven would take a hr to heat up

  • Customer: Eddie from Herrin IL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
two screws two wires two min its to easy

The bake element had burned out.

  • Customer: Patricia from Indianapolis IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
My son took out the burned out bake element and installed the new bake element. Not hard at all. The new element arrived at my home in one day. Thanks.

needed new drip bowls for stovetop GE

  • Customer: Patricia from Centereach NY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
removed the burners and dropped the drip bowls in. Very easy to do,

stained drip bowls

  • Customer: Sunny from Salt Lake City UT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
unplugged burners replaced drip bowls plugged in burners

Bake element went up in smoke.

  • Customer: Donald from Pleasant Grove AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
1 Turn off power at circuit breaker. 2. Use nut driver to remove the two screws holding element. 3.Remove panel on back off stove to get to the 2 wires that go to unit. The wires will slip right off the element. 4. Remove old element.5.Slide in new element being careful to go through old holes in insulation. 5 P ut the two screws back to hold element. 6. Connett the wire in back to element. 7 Put cover back on. 8. Turn circuit breaker back on. Very easy job.

Replaced lower burner

  • Customer: Steven from Brunswick OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the racks, used nut driver to remove bolts and pulled old burner out. Pulled connections out of the back of oven wall. Set new burner and connections and replaced screws with nut driver.

Bottom trim on oven door rusted - poor GE design

  • Customer: Wallace from Vestal NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
In order to replace the bottom trim (and side trims if needed) it is necessary to separate the oven door front panel and its outer glass from the inside door panel. It is best to remove the entire oven door and lay it down on a table in order to do this. (Refer to owner's manual for instructions on removing the door from the oven, but it basically lifts out easily when is is in the broil-open position). Remove the front panel of the oven door by unscrewing the two machine screws (these may be torx head screws on your appliance) on the top inside corners of the door that hold the door handle. (screw spacers on the inside likely will fall out when you remove the machine screws - don't be alarmed) Then remove the three screws at the bottom of door trim. The front panel can then be lifted away from the back panel. This will allow access to the screws that hold the bottom trim to the side trim. Remove these and the bottom trim will slide off. Replace trim pieces and reassemble.

Bottom baking element bit the big one

  • Customer: Jon from Apache Junction AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
First–removed the door. Very simple—lower the small latch on each hinge from the stove side DOWN to the door side to unlock. Second–crawled into the oven to reach the two screws holding on the bake element. Pulled out the element (wires are VERY short) to see if I had a screw-on or the push-on type. Third–went to PartSelect to order the correct element. Waited a few days for shipping to arrive. Fourth–just reversed the steps to install the new bake element. Fifth–installed the door and secured the locking latch back up to the oven side. Sixth–made me some HOT WINGS!

Bottom Drawer Guide Broken

  • Customer: Bill from Knoxville TN
  • Difficulty: Very Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
The replacement bottom drawer guides were not the same part as described in diagram. The front drawer guides which were also ordered were fine. I could not use the bottom drawer guides, however due to the modest cost of the part and shipping costs, I did not return.

GE Electric Range rear left burner quit coming on

  • Customer: Richard from Richmond TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Pliers
  • 0 of 0 people found this instruction helpful
Removed the back top cover with 1/4" nutdriver. Removed the burner terminal block with 1/4" nutdriver. Within 15 minutes had the terminal block kit removed and installed and in service.

Needed to replace drip bowls

  • Customer: Gloria from Dallas TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Husband just snapped in place in about 8 seconds! Thanks for the fast delivery and pleasant staff assistant.
All Instructions for the 91193402992
256-270 of 273