9112XUB Magic Chef Range - Instructions

removed cover over burner section ,removed power to burner section ,removed burner assembly, replaced ignitor assembly, wire in to control circuit ,replace burner section in oven,turnon power chech operation ,replace cover.

Removed door, took off old igniter. Had to redo plug , simple, because kit had wires to splice to make it work. Whole job was 30 min. Recomend to anyone. Saved $75 on a service call. Bill

Initially found timer/board faulty. Replaced with new. OK. Then found the ignitor lighting but the flame not starting for the burner. Upon doing research on this oven, I found the ignitor opens the oven valve by a high amperage draw. The ignitor was starting but not glowing bright enough, or drawing enough amps to open the gas valve. If the ceramic on the ignitor is gray,or "chalky" looking, change it. It may open the valve faster and your oven will perform better. Just because the ignitor is lit doesn't mean its working correctly.

removed inside trays and grill inside large oven door on front to get to ignitor,removed ignitor with 1/4 drive socket,followed the wires off the ignitor thru the hole in back of oven and disconnected the connector,put on in reverse order.To simple to even write about,anyone can look at it and tell what needs to be done

Remove old igniter ,,again had to remove rear panel of unit to get to connecter..reverse procedure to install igniter. Video very helpful.

DISCONNECT AC ELECTRICAL POWER TO RANGE AND TURN OFF GAS SUPPLY TO RANGE 1. Removed door (slide up and off hinges), no tools required. 2. Removed grate/s and burner cover to expose burner and igniter. 3. Used hex socket tool to remove two igniter bracket screws. 4. Carefully pull two woven glass insulated leads connected to igniter until connector is in reach. 5. Use care not to put unnecessary strain on leads and connector body. 5. Squeeze locking tongs of connector, and unplug igniter leads. 6. While holding female end of connector, insert new igniter electrical plug, making certain they latch together. 7. Carefully push excess leads / connector body into recessed area and wrap insulation supplied with igniter kit around glass woven leads of igniter, to re-insulate the cavity opening. 8. Position igniter on burner tube bracket and replace hex screw fasteners. 9. Plug in electrical power to range, turn on gas supply. Check oven for proper operation. If oven does not light, shut off gas supply, unplug electrical power and contact qualified service technician.

really easy thank you to your video

My son-in-law unscrewed the front panel AFTER shutting off the power to the oven. He located the thermostat and easily replaced it, then screwed the front panel back in place, turned on the power and we like the results. The oven reaches the desired set temperatue.

Nothing to it. Took only a few seconds. Just slipped on the new knob and it was good-to-go!

Make sure power to the oven is disconnected. Remove all shelves. Partially open the bottom door and yank it out so it is out of your way. The igniter is next to the back and upper wall of the oven inside the lower (broiler) compartment. The igniter is held by two screws which I opened using a 5/16 or 8mm nut driver. After removing the two screws, remove the back plate using a regular phillips screwdriver. Next, pull out the two igniter wires until the connector comes out. Pressing the side tabs disconnect the igniter from the connector. Connect the new igniter. If nesessary, replenish some of the insulation with new insulation that arrived with the new igniter. Push excessive igniter wiring back, remount the backplate using the phillips screwdriver. Remount the new igniter using the nutdriver. Remount the bottom door. Put all shelves back. You are done.

There were NO directions in the box, only a schematic. I was unable to locate the old one as my husband had removed it. So I had to guess which color wire connected to which plug. Good thing I guessed right the 1st time! so you might want to include installation instructions going forward.

To replace Gas valve, turn off gas to oven and shut off electrical. Remove all oven bottoms (lift out)access to gas valve is in back of broiler section. Remove cover over gas valve(2)screws, remove gas line attached to gas valve, remove wires from gas valve remove (3) screws from mount holding the valve. Pull valve assembly out and remove valve from mount. Install new valve in reverse order.

I am so gald I found Parts select. I was going to order a Gas valve for $140. All the comments said the problem was a bad igniter. even though the igniter was glowing bright it was not drawing enough pawer to open the gas valve. I purchased the igniter installed it in 15 minutes and my oven works like new.

Compressed the springs and removed the damaged switch, then changed the wiring over to the new switch and press into place, worked fine.

Followed the excellent instructions on your web site. I removed the oven burner assembly to make it easier to install the new igniter. The connector on the new igniter matched the one in my oven exactly. It helps to have the oven light on!