Models > 9112WUV > Instructions

9112WUV Magic Chef Oven - Instructions

All installation instructions for 9112WUV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9112WUV
46-60 of 198
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

broke the igniter in the oven before I even got the oven installed

  • Customer: june from wills point TX
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
ordered the new igniter kit, it was delivered the NEXT day, followed the instructions, it was a lot easier then my old Tappan oven, took about 15 minutes. Not bad at all, and I am a 58 year old woman.

oven would not light

  • Customer: gary from covington LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 1 of 1 people found this instruction helpful
New parts matched up perfectly. Undid screws holding old igniter, hardest part of procedure because one screw was frozen and broke off. Pulled stove out and new igniter"s connector was identical. Pushed stove back into place and it lighted on the first try.

Oven was not working at all

  • Customer: Glynne from Dedham MA
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 1 of 1 people found this instruction helpful
My brother is a handyman. The part was delivered very quickly. The instructions were very easy to read and after an hour, voila the oven works perfectly!

light bulb went out in my oven

  • Customer: Janet from Ada MI
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
My husband took the plastic cover off and took out old bulb and screwed in the new one. Then put the cover back on.

Replaced a broken hinge.

  • Customer: Joseph from New Windsor NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 2 of 4 people found this instruction helpful
The repair was easy. The door pulls off the hinges without any tools. I had to remove four screws ihat held the wall oven in place. I then removed approximately eight trim screws to expose the two screws holding the hinge in place.I then needed to utilize a nut driver to put the screws in the new hinges because the screws cut threads into the hinge as you put them in so they are a little tight and the nut driver makes this step easier.

Oven making whooshing sound and not heating up

  • Customer: Jason from Williamsburg VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Pulled oven out from wall. Unplugged. Pulled out bottom drawer. Removed oven door by pulling up on angle. Removed bottom of oven. Removed old ignitor by taking out screws. Disconnected red and white wiring plastic coupler. Fed new wiring and connected. Mounted ignitor. Plugged back in. Very easy and worked!

IGNITER WOULD GLOW BUT STOVE WOULDN'T LIGHT

  • Customer: ALAN from LUCK WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
I NOTICED THAT THE IGNITOR WOULD GLOW BUT THE STOVE WOULDN'T LIGHT - I GOT THE MODEL NUMBER OF THE STOVE AND GOOGLED THE MAYTAG MODEL NUMBER. CAME UPON YOUR WEBSITE AND REALIZED THAT 94% OF THE TIME THE PROBLEM WAS THE AMPS WERE NOT ENOUGH TO LIGHT THE STOVE. I LOOKED AT ALL OF THE STORIES ON HOW EASY IT WAS TO FIX. I ORDERED THE PART AND RECEIVED IT WITHIN 3 DAYS. I OPENED THE DOOR PART WAY AND LIFTED IT STRAIGHT UP TO REMOVE IT. I PULLED OUT THE BOTTOM BROILER PLATE BY GRABBING THE BACK ON PULLING UP. I UNDSCREWED THE WING NUT OF THE FLAME BAR AND HAD EASY ACCESS TO THE IGNITER. I REMOVED THE TWO NUTS FROM THE OLD IGNITER. UNPLUGGED THE IGNITER FROM THE EASY ACCESS DOOR FROM THE BACK AND PLUGGED IN THE NEW IGNITER. REPLACED THE ACCESS DOOR AND ATTACHED THE IGNITER WITH THE TWO NUTS. PUT THE FLAME BAR BACK ON, PUT THE BROILER PLATE BACK ON, PUT THE DOOR BACK ON, PLUGGED IN THE STOVE TURNED IT ON AND SUCCESS. IT WAS SO EASY. I KNOW IN OUR AREA I WOULD HAVE PAID NEAR $200 FOR A SERVICE TECHNICIAN TO COME OUT AND DO WHAT I DID IN APPROX. 20 MINUTES AND $50 FOR THE PART. THANK YOU SO MUCH FOR YOU WEBSITE TO HELP US NOT SO TALENTED APPLIANCE REPAIR HOMEOWNERS.

Replacement of igniter

  • Customer: Robert from Orange CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Removed two nuts and one screw to replace old igniter with new one. Replaced the nuts and screw. Turned on the oven, and it is working fine.

Oven Ignitor went to ignitor heaven.

  • Customer: Brian from Pittsburgh PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 1 of 2 people found this instruction helpful
The repair was real easy, other than the old bolts which just turned in the sockets when trying to get them out. It might be a good idea to provide two nuts and bolts to negate this problem. I would not mind paying a dollar or two extra for two bolts and nuts. Other than that, the instructions were clear. Product arrived on time and I would absolutely use your services again. Oven is back to working great! Thank you!

Oven did not ignite

  • Customer: John from Racine WI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
Remove the door... it just pulls up and out... set the release tabs so you can remove the bottom plate .. pull out broiler drawer... unscrew the 2 screws on the igniter ..let that hang... remove the cover for the termination.. and unplug the old igniter... then reverse everything to put back together..

oven took too long to light, then lit with a whump sound

  • Customer: Steve from Sierra Madre CA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 1 of 2 people found this instruction helpful
I read all the reports on your site pertaining to oven igniters and decided to order one. I was amazed when it arrived the next day. I got a lot of tips reading others replys so I lifted off the oven door, took out the racks, removed the 2 screws holding the old igniter and tried to pull it out. There was hardly any slack in the wires, so I pulled the stove away from the wall, took off a breadpan size cover in back and found the wires were zip tied to a tube. I cut the tie and unplugged the wires, but the new plug didn't match so I cut the new plug off and rejoined the wires with butt to butt crimp connecters, which I prefer to wire nuts. I used the insulation and new cover from your kit as my old part had the long ceramic insulator and put it all back together. It works like new again and saved me a lot of money. I am very pleased with your product and service, thanks.

smell gas and sometimes a whoof on ignition

  • Customer: Maynard from Knox IN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
I removed the flame baffle , removed the two screws that held the ignitor. Then I pulled the wires thru the back wall and disconnected . I had to cut the the connector and install with wire nuts because connector was different. Works fine now .

Bottom oven burner wouldn't light.

  • Customer: James from Lino Lakes MN
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
If your igniter glows but the burner doesn't light, your igniter is more than likely bad. It should have at least 3.2V to gas valve when the igniter is glowing in order to open the gas valve. The repair is very easy with only a 5/16" nut driver equired to remove and replace the igniter. It's pretty much a plug and play reair.

oven would not light , smell of gas

  • Customer: jerry from staten island NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 2 people found this instruction helpful
removed oven floor, removed two screws in element . pulled out element wires, secured them so they would not fall back into slot, snaped in new element . scewed it in place , replaced floor . thanks partselect.com

Oven would'nt heat

  • Customer: Ariel from Oxford NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 1 of 2 people found this instruction helpful
First I removed the two screws that held the old element in place. I then pulled the element out about 3 inches and disconnected the two wires.
I replaced the element with the new one and tucked the connector in the insulation. Additional insulation came with the kit. I replaced the two screws that held the element in placed. Oven worked perfectly
All Instructions for the 9112WUV
46-60 of 198