Models > 9112WUV > Instructions

9112WUV Magic Chef Oven - Instructions

All installation instructions for 9112WUV parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9112WUV
181-195 of 198
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Digital clock/timer broken

  • Customer: Jennie from kingwood TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
There were NO directions in the box, only a schematic. I was unable to locate the old one as my husband had removed it. So I had to guess which color wire connected to which plug. Good thing I guessed right the 1st time! so you might want to include installation instructions going forward.

Ignighter comes on but gas will not

  • Customer: Wayne from Vacaville CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
To replace Gas valve, turn off gas to oven and shut off electrical. Remove all oven bottoms (lift out)access to gas valve is in back of broiler section. Remove cover over gas valve(2)screws, remove gas line attached to gas valve, remove wires from gas valve remove (3) screws from mount holding the valve. Pull valve assembly out and remove valve from mount. Install new valve in reverse order.

Oven Would not Light

  • Customer: Neville from Lithonia GA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Remove door. Disconnect power supply from the range.Remove shelves.Remove burner and disconnect power from igniter.Remove bad igniter and replace with new one,reconnect igniter to power supply. Replace burner and all parts that were removed.Re- connect appliance to power source. Range is ready to be used.

Oven would not ligth, igniter did get red.

  • Customer: Fred from Juneau AK
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I replaced the igniter, several people on this site agreed that this is the problem and they where rigth.I t was an easy fix. I live 60 miles from the next town and repair shop. I am out in the Alaska bush and can only get to my place by boat or by floatplane. Thank you all you self fixers for your help.

The oven would light, but the flame was very small and it took 30 minutes to preheat.

  • Customer: Bradley from Louisville KY
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Watch the video, it's too easy and best of all, the part fixed the oven!

heating was suddenly high and constant

  • Customer: freddy from duncanville TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Changed out the thermostat, very easy to do. The instructions were the same as I read on this site on a similar fix. HOWEVER, even after making the thermostat change, the heat did not regulate or adjust. Not sure if part is bad, or something else could be the culprit? but if not thermostat which regulates this, what could it be? I'm very impressed with PartSelect as a company and their website is great, but i'm baffled as to this ongoing problem.

Bulb replacement

  • Customer: Judith from Phoenix AZ
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
I pulled down the wire around the glass cover...released on end of the wire from its holder being careful to not let the glass cover drop. Unscrewed the bulb and replaced with replacement. Easy, easy.

Oven Failed to light

  • Customer: Mark from Middletown NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Once I noticed the oven failed to light, I checked the igniter and saw it was glowing. At that point I did some research and found that the igniter could still be bad even though it glowed. This was the most common cause of ovens not lighting. A bad igniter will not glow as bright as a new one. An igniter had to draw a minimum of 2.8 amps in order for the safety valve to open and supply gas to the burner. After checking the safety valve with an ohmmeter, I found it to be good, so I ordered a new igniter. Once I received the new part , it took about 20 minutes to install.

Two mounting screws were bonded from heat and stripped the threads.

  • Customer: Donald from Dixon IL
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Replaced stripped screws with 632 by 3/8 bolts and nuts. Your video helped with the rest of the installation.

igniter would glow but oven would not light

  • Customer: Roberto from New York NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug power cord to oven.Remove lower panel from inside of oven to access flame rail cover.Remove wingnut from cover to access flamerail and igniter.Using phillips head screwdriver,remove 2 screws from lower access plate located at rear of oven to access igniter wiring.Disconnect both wires, then using a nutdriver,unscrew and remove igniter from flamerail.To install, simply reverse instructions.It was extremely simple and fun to do.But most rewarding of all was the sense of accomplishment from doing the repair myself not to mention of course the money i saved not having to call a technician. Thanks guys!

As with the majority, igniter would glow, oven would not light.

  • Customer: Glenn from Mentor OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Because of the video provided by Parts Select I felt confident before even starting and that confidence stayed with me to the end..I removed bottom of oven , removed the philips screw in the front end of the burner and removed it.. Losened and removed the igniter replaced it and reassembled..The only caution I can give, if you find the screws holding the ignited on the burner hard to take off, apply a SMALL amount of WD40 to the threads and wait a couple minutes before removing..I was fortunat in the fact that my plug matched the replacement part with no cutting of wires..I normally don't get breaks like that.. Thanks Parts Select.

Oven would not light

  • Customer: Angela from Staten Island NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
First turn gas off at pipe. Remove oven door, racks and bottom cover. Go to back of oven and unplug oven igniter. Back in front, unscrew 2 nut screws from igniter. To make things easier I tied a piece of string to the plug of the igniter, once I unscrewed the igniter I pulled it out with the string attached. When replacing I tied the string to the plug of the new igniter and pulled it from the back so the plug was able to come through, plug in the new igniter, screw it in place, replace the racks, covers, door and you're ready to enjoy some baking

Oven very slow to preheat

  • Customer: Zach from Austin MN
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Based off the information I found online, I determined we had a bad igniter. 1- disconnect oven from any power sources. If you have a gas model, be sure to valve off gas at this time as well. 2- Remove the racks and bottom pan in the oven. There is 2 push/pull locking mechanisms at the back of the oven that hold the tray in. Once you have this out you should have access to the gas tube and igniter. 3- Using a 5/16 nut driver, remove the 2 bolts on the mounting plate and the igniter should be free at this time. 4- Remove the bottom drawer to the oven. This will give you access to the electrical connections. 5- Remove the 2-3 screws that hold on the access panel toward the back of the unit. 6- Following the wires down, find the plug for the igniter and unplug. After this is done pull the wiring up through the oven and it will be the same to put back together just in reverse order. Relatively simple project that should take anywhere from 10-30 minutes depending on how handy you are. After reinstallation our preheat times went from 45 minutes to 10

Oven burner ignitor would glow but burner would not light.

  • Customer: Daniel from Moreno Valley CA
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Hardest part was disconnecting the gas line and moving the range out of the counter. Removed oven door for easier access to the igniter from the front. And the clean up. Installing the igniter was relatively easy from the rear of the range. I was not able to install the igniter through the front of the range because the wires were not long enough to pull the igniter forward through the front so it was necessary to pull the range out from the counter and install it from the rear. Then it was just a matter of removing a small dust cover at the rear by removing one screw. Then removing old insulation and disconnecting wires. Remove 2 mounting screws that held the igniter in place. These screws had to be removed from the front. Pushed the old igniter out through the rear of the range. Connected the new igniter wires. Pushed the new igniter through the rear of range and replace the new insulation. Mounted the new igniter with 2 screws. Reassembled everything and it worked ok.

oven ignitor not opening the gas valve

  • Customer: Thomas from highlands TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
removed cover over burner section ,removed power to burner section ,removed burner assembly, replaced ignitor assembly, wire in to control circuit ,replace burner section in oven,turnon power chech operation ,replace cover.
All Instructions for the 9112WUV
181-195 of 198