Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 9112WUA > Instructions

9112WUA Magic Chef Range - Instructions

All installation instructions for 9112WUA parts

These instructions have been submitted by other PartSelect customers and can help guide you through the range repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 9112WUA
16-30 of 206
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven wouldn't ignite

  • Customer: Treasure from High Point, NC
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
First I unpuged the Range. Then I removed all racks and bottom tray of oven.
The Ignitor is located at back of oven, paralelle to the gas bar. I removed the 2 screws holding the ignitor and unpluged the wires. Then I put on the new ignitor, perfect fit, replaced the 2 screws and pluged in the wires , then pluged in the range. I turned the oven on and it lit in about 10 seconds.
Thank you PartSelect for having such a wide range of range & oven parts . no one should have to pay a service tech. to fix most problems, as long as we have a GREAT SITE LIKE THIS ONE.
p.s. You guy also had one of the lowest prices , my part arrived ahead of schedule .
THANKS A LOT !

oven won't stay light

  • Customer: Shannon from Lake Park, IA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 8 of 8 people found this instruction helpful
removed racks, bottom plate. removed screws with a little bit of help from cooking spray. Unclipped old ignitor clipped in new ignitor, used old screws, and inserted insulation replaced racks, bottom shelf. Turn on oven and worked, been using it for about a week now. PS. ordered on monday morning arrived wednesday afternoon.

needed a rack for my oven

  • Customer: steve from herald, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 10 of 15 people found this instruction helpful
i needed a rack for my oven i looked everywhere for one that fit could not find one.my oven is not common due to the fact it is for a very small space and only 18 " wide i stumbled on this site by accident and decided to try it out shipping was very fast and people there are very nice any have alot of knoldge about parts it is very well set up to order with just a modle # i have told my whole familey about this site they did a great job and i will be back for more parts.

Oven wouldn't ignite

  • Customer: John from Caliente, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 8 of 10 people found this instruction helpful
Removed oven door (easy it lifted right off) and remove oven bottom (also easy, no tools). removed two screws holding igniter and unplug old igniter from power. Re-attached new igniter and re-assembled oven.

Parts came very quickly from PartSelect. Good service.

Replaced a broken hinge.

  • Customer: Joseph from New Windsor, NY
  • Difficulty: Really Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 6 of 8 people found this instruction helpful
The repair was easy. The door pulls off the hinges without any tools. I had to remove four screws ihat held the wall oven in place. I then removed approximately eight trim screws to expose the two screws holding the hinge in place.I then needed to utilize a nut driver to put the screws in the new hinges because the screws cut threads into the hinge as you put them in so they are a little tight and the nut driver makes this step easier.

Heat was escaping from my oven and really heating up my house

  • Customer: Patricia from Sanger, TX
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 5 of 6 people found this instruction helpful
The heat sealing strips are elastic type material with hooks on each end. I simply removed the old strips and hooked the new ones in place.
It was easier than I ever dreamed possible!
And my kitchen is now nice and cool.
Pat Morrison
Sanger TX

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell, WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 5 of 7 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

oven would not turn on flame

  • Customer: Michael from Secaucus, NJ
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench (Adjustable)
  • 5 of 8 people found this instruction helpful
first I removed the 6 screws that hold the oven in place in the oak cabinet. I slid a kitchen chair in place in front of the oven,then I slid the oven out of the cabinet cut out. Although the gas flex was still connected, I unpluged the electrical connection. I removed the old igniter, unpluged the igniter harness in the rear compartment. Then I installed the igniter in reverse.When the oven was pushed back in and secured with the 6 screws,I turned on and tested. Igniter glowed orange and the flame came on. Job was complete in 20 minutes.

Replaced Oven/Broiler Knob

  • Customer: William from Santa Rosa, CA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 4 of 5 people found this instruction helpful
All I had to do was slide it on. The hard part was that I could not find the modle number anywhere, and your web site showed me possible places to look, so that I was able to find the modle and order the part that I needed.
Thanks so very much, William Millard.

The oven igniter lit up but the valve wouldn't release the gas to ignite.

  • Customer: John from Wisconsin Rapids, WI
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers
  • 3 of 3 people found this instruction helpful
I would have never guessed that the problem would have been with the igniter since it was glowing. After reading some of the entries in your trouble shooting area it was clear that this is common and that it likely was the igniter so I simply took off the two screws that hold it in place, inplugged the old, plugged in the new, secured with the screws and it worked. The only problem I encountered was that when I unplugged the old igniter the plug fell down into the bowels of the oven and I had to fish out with a twisted up hanger.

Oven would not maintain temperature

  • Customer: Gregory from Mamaroneck, NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 5 of 9 people found this instruction helpful
Gas was turned off! Valve control cover was removed. Inlet fiting to valve was disconnected. Wires were removed from valve. Valve attachment assembly was removed. Old valve swapped out for new on attachment bracket. New attachment assembly affixed into oven. Wires connected. Valve control cover assembled. Gas turned back on and tested. Voila - cornbread the next morning!

I needed a broiler pan

  • Customer: Rhoda P. from Secaucus, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 4 of 7 people found this instruction helpful
I took the broiler pan out of the shipping container and put it in the oven.

Oven burner would periodically go out and re-light

  • Customer: Richard from Merrimac, MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench set
  • 3 of 4 people found this instruction helpful
The ignitor is held on by two screws which were rusted in place. When I tried to remove them, the screws became stripped and had to be cut off.

Once the part was free, the rest of the repair went quickly . At that point:
- Pull the element leads enough to get to the plastic connector
- Disconnect the old part
- Connect the new part
- Re-attach to the bracket with new screws.

oven wouldn't light

  • Customer: peter from marine city, MI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
The gas valve (recently new from partselect) wouldn't open, or sometimes it would open just enough to let some gas escape! I read from others that just because the igniter was glowing, it might not be putting out enough voltage to trip the gas valve. A check of this confirmed that it was sending just over 3V to the valve - not enough to fully open it. I felt confident that springing for the $60 would solve the problem once and for all. After replacing the igniter, the oven lights in 10 sec or less, and this is a 26-year-old appliance! PartSelect to the rescue again!

Igniter glowed but oven would not light

  • Customer: Richard from West Mifflin, PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 2 of 2 people found this instruction helpful
The repair was straight forward. Turn off gas, unplug stove. Remove the oven door by opening slightly and lifting straight up. The bottom plate lifts from the back. Remove two screws and plug; install new unit. Turn everything back on; proceed with baking...
All Instructions for the 9112WUA
16-30 of 206