Models > 876B > Instructions

876B Amana Oven - Instructions

All installation instructions for 876B parts

These instructions have been submitted by other PartSelect customers and can help guide you through the oven repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 876B
1-15 of 28
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Oven element burnt out and broke apart.

  • Customer: Lana from Pineville WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 11 of 12 people found this instruction helpful
After ordering the element, found out it was the wrong element, I needed an 18.5 inch x 15.5 instead of the 15 1/4 x 15 1/2"...I slowly bent the element in shape to fit my oven. It works beautiful.
But for you guys, order the right one. Don't forget to measure your old elements spread from connection to connection. Install the new element and then test to be sure it works proper.

microwave oven blew fuse

  • Customer: tad from tamarack MN
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 12 of 18 people found this instruction helpful
First I removed upper front grill by removing two Philips head screws on top and pulling off. This exposed the Philips head screw which holds control panel in place. After removing screw I pushed up on panel and it came off to expose fuse. With needle nose pliers I removed old fuse and again with pliers held new fuse in position. With the help of a bladed screwdriver, I pushed new fuse into holder, then replaced panel, screw and grill. This took less than 15 minutes even as one of the wires on control panel pulled out of connection and took some time to locate where to reconnect, otherwise was an easy fix
.

Died while heating lasagna

  • Customer: connie from madison NC
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 6 of 11 people found this instruction helpful
Removed 4 small star head screws from back of microwave, lifted body off, removed blown fuse and replaced with new one (found where cord enters). This model is stainless inside and out and I like it a lot. It is also sold by Daewoo and a few other manufacturers.

Replacing the bulb in the freezer side

  • Customer: Yafa (and David) from Bothell WA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 4 of 5 people found this instruction helpful
Removed the ice brucket,
Removed the light shield by releasing one screw using a nutdriver.
Replacing the bulb and reinstalled the light shield.

Your web site is one of the best and most helpfull service sites I ever used. Just wish that in the future you will ship parts overseas.

Element broken, oven would'nt heat

  • Customer: frances from Coffee Springs AL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 3 of 4 people found this instruction helpful
First I removed the two screws that hold the element in place. Then I pulled the element out about 3 inches and disconnected the two wires. Reconnected the new wires, put the screws back in and the oven WORKED!!

oven element burnt out

  • Customer: elizabeth glennon from rochester MA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 3 of 4 people found this instruction helpful
The cost of new ovens and a having an electrician come out to fix was ridiculous.We looked online fro an alternative and found your part w/ picture (which helped) for only 41.00 w/ tax to fix! We recieved item within 4 days and we fixed it in about 15 min. Thank you so much for saving us tons of money and loads of headache!

oven light burnt out

  • Customer: William from Schwenksville PA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 3 of 4 people found this instruction helpful
1. Unscrewed glass cover on bulb
2. Removed old bulb
3. Screwed in new bulb
4. Replaced glass cover
5. Mixed drink & baked cupcakes

microve stopped working

  • Customer: Denice from Montgomery AL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 5 of 11 people found this instruction helpful
Jenn-Air Microwave would not turn on. Clock worked , light worked, timer worked and would count down .I changed' Part #0813140 Switch, Micr} cost $8.99 plus shippingNow it works Thank You for good advise

Heating element burned out...forcing me to replace it.

  • Customer: Stephen from Cedar Rapids IA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 2 people found this instruction helpful
Our oven is a wall mounted oven so I could not reach the plugin. Therefore I shut the power off at our breaker box. I then removed the screws that held the old heating element to the oven. Removed the element, slipped connecting wires off of the old element. Next I slipped the connector wires onto the new element and replaced the screws. Turned the power back and and checked to see if oven worked. It did! As you can tell I am a novice at home repair but this worked perfectly!

bake element needed replacement and then some...

  • Customer: Steve from Rose Hill KS
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
Check the connectors first and the associated wiring, as our stove had been stricken by lightning a couple of years ago. Seems the stove was fairly new we had a service tech replace the stove top relays to correct the shorted out stove top. Unfortunately no one checked the rest of the stove as the oven elements still functioned. What I realized when the bake element failed was the lead wire to the bake element was actually shorted from the lightning to the stove and the element was damaged but still worked. The lead wire was trimmed back and the connector replaced along with the element. The lightning had damaged the unit and luckily we don't bake much as it actually had soldered the connector to the back of the stove. Lesson learned...if your appliance it struck by lightning remove the back and check to assure your stove will operate safely. Thanks for the prompt shipping as everything is good as new now and we are much safer too.

The element gave out

  • Customer: Marlin from Lincoln MO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 1 of 1 people found this instruction helpful
I just had to take 4 screws out and pull it out and put the new one back in!!

The oven wouldn't bake anymore.

  • Customer: Cheryl from Tallahassee FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
First I removed the two screws that held the element in place. Then after slightly pulling out the wires, I disconnected the two wires on each side. The new part just snapped into the old wires. I pushed the element back into place, replaced the original two screws to hold it into place, and it was all done! Two screws and two wires...done. It took about 2 minutes and this is something I have NEVER done before. The oven works beautifully now!

light wont come on

  • Customer: James from Fort Collins CO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Wrench set
  • 2 of 4 people found this instruction helpful
Well, when you put the back cover on and screw it down make sure you have nothing touching the white wire leading to the oven light. I did and it blew the push switch when I threw the 220 breaker. Actually, the light was on when I came in the room, but when I pushed the switch on the front panel it sparked in the rear and popped the breaker. Then I saw the short and when I tested the switch it would not click. The install was fine.

bottom burner was burned in half

  • Customer: Anthony from Social Circle GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 1 of 1 people found this instruction helpful
It was very easy,it took five minutes to replace it. I disconnected the two leeds from old burner and connected them to the new one.

Element burned up

  • Customer: Susan from Springfield CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
On the Saturday before Christmas, during some baking, my heating element we out of my oven! Since I was cooking Christmas dinner at my house on Thursday, I freaked out. Fortunately, we got on the interenet, ordered a new element, paid for 2-3 day shipping, and received it on Wed. afternoon. My husband unscrewed the old element, and put the new one in about 5 minutes. Very easy job, and Christmas was a total success!
All Instructions for the 876B
1-15 of 28