Models > 7MNTM5000TQ0 Whirlpool

7MNTM5000TQ0 Whirlpool Washer - Overview

Get Parts and Repair Help for 7MNTM5000TQ0

If you know the washer repair part you need, you can browse the list of all parts on the 7MNTM5000TQ0, or you can search by name or part description. You can also find your part by where it is located on the 7MNTM5000TQ0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 7MNTM5000TQ0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$3.32

Agitator Directional Cogs

These agitator directional cogs are commonly referred to as dog ears. They come four to a package and are usually used with direct drive washing machines.

$11.77

Direct Drive Motor Coupling

This coupling kit is used between the motor and the transmission on direct drive washers with no belt. This is the newer version and is made with new metal sleeves for added strength.

$29.84

Direct Drive Water Pump

It is intended for use with washing machines that do not have belts. This drain pump has two ports for water to pass through: a large one, and a smaller one.

$2.52

Suspension Spring

Sold Individually. Appliance takes 3 of this part.

$28.77

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$17.97

Water Inlet Valve with Mounting Bracket

This part could have either a blue colored valve body or a green colored valve body. There are two ports for water to enter and this valve is compatible with a half inch ID hose. It has two 3/4-11x1/2 NHT hose threads.

$21.75

Lid Switch

The pin on the lid pushes on the lever of the lid switch to tell the machine that the lid is closed. This part includes the grounding wire.

$4.46

Agitator Bolt

This kit contains one screw with rubber gasket and threaded sealant. The screw head is 7/16".

$2.52

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. Th...

$3.76

Tub Spring

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

REPLACE WATER PUMP COUPLING

  • Customer: RICHARD from PHILA PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers, Socket set, Wrench set
  • 489 of 497 people found this instruction helpful
REMOVED CASING TIP OVER WASHER DISCONNECTED WATER PUMP. DISCONNECTED MOTOR THEN REPLACE COUPLING THEN REASSEMBLE MOTOR THEN REPLACED WATER PUMP. read more

washer wouldn't agitate

  • Customer: mike from Kent WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 484 of 490 people found this instruction helpful
First pry off the cap of the agitator. Then using a socket remove the bolt that holds the plastic cup in place. Remove this cup by prying it loose from the two tabs that hold it in place. Once this cup is removed you can get to the broken cogs.
Slip the new cogs into the underside of the cup, and slide the cup back down in the agitator housing usin... read more

Washer not agitating

  • Customer: Craig from Polk City FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Socket set
  • 462 of 462 people found this instruction helpful
On top of the agitator is a flat cap that is held in place by the friction of an o-ring, there are no fasteners. I would imagine one could get under the lip with a small screwdriver or butter knife to pop it off but I chose simply using my fingernails so as to not disfigure the cap. Under the cap you will find the head of the only bolt that holds the assem... read more