7MNTH8000TQ0 Washer - Instructions

remove the back panel and replacement went real easy once the panel was really easy. perfect fit

Followed the video and instructions included with part. At first we did not think the repair was successful, but after several small loads were run, squealing stopped. The washer is 16 years old and so far is running like new. We certainly appreciated the great customer service. The part was delivered in less than 24 hours.

very easy, pop up the top, unscrew 2 screws, unplug switch , plug in new switch replace 2 screws ,put top down,finished

The repair took about an hour. My wife told me the washer was so quite that she had to check and make sure it was running. It was like getting a new washer for less than 30 dollars. I've saved Part Select web site to my favorites and will use your company again.

I watched the short video that was in the email with my order confirmation and all turned out well.

As directed on the informational vídeo shown on the website with just a few diferences....bit otherwise got the honey do list item fixed....

Unplugged the washer and unscrewed hoses. Unscrewed the 2 screws on the back of the control panel and folding it up. Took off the 2 metal ties to get the cabinet off. Once off, I unscrewed the ground from the old Lid Switch and popped out. Put the new Lid Switch in, screwed the ground back in, replaced cabinet, clamps, put the control panel back in place and screwed the 2 screws on back of the control panel back in. Screwed the hoses back on, plugged the washer back in, everything works great again.

Watched the videos that were very helpful and repaired it my self with no problems its fixed and running like new i took a little extra time to clean all of the washer since i had it apart any ways so the time to fix it was probably was a little shorter i would like to thank part select for all there help and videos it made this job so much easier.

After some research, it seemed like the water pump was the culprit since I knew all of the hoses were good. My washer was a little different from the one in the repair video. My washer didn't have the gauges on a hinge, so it sort of had to hang there. Also, there were no spring clips on the interface/dashboard, there were screws at the back of the washer that I had to unscrew which allowed me to lift up the dashboard so that I could remove the clips from the back to the main panel that surrounds the front/sides. Because my washer was old, I had the most difficulty just pulling the old pump off and putting the side/front panel back on the front of the machine. The video was obviously from a guy replacing a part on a brand new washing machine. Just work the part gently back and forth and you should be able to remove if it doesn't come off right away. I've run 2 loads of laundry through the washing machine with no leaks, so this fix was cheap and awesome!

There are youtube vids on how to get the thing open. I just wish I'd known the following: 1.remove agitator BEFORE opening the unit up and leaning it back (much easier to work inside the tube with it upright). 2. be aware that a free-floating part known as the skate plate can dislodge while the unit is on it's side/back. It is a generally triangular piece of flat-ish metal between the base of the tub and the top of the drive-train chassis. If it doesn't line up properly after you replace the parts you're going to get a noisy, clanking spin cycle the next time you run the thing (as I discovered).

The prooblem started with the hole in the bottom frame, for tub spring wore through, spring fell off, then a spring retainer worn broke in 2 releasing 1 suspention spring. All springs were about to fail, metal very thin at at the contact points. Drilled a new hole for the new suspension spring, replace all 3 brackets, worn also, springs, and retainers with a small dab of grease at the contact points. The new springs mad the tub more stable than before the failure, and silent when spinning or washing. Be careful to get the springs in the right direction, then the spring comes over the outside the brackets and retainers, other way they rub in spots. On this machine one was backwards from the factory 18 years ago, surely that accounts for more stable running.

Remove softener dispenser. It is hard to do, but it does pop off. Reach down inside and remove the cover. The cover has a handle. Clean the rubber gasket. The bolt holding the agitator can be removed with a socket. You will need a 12" extension. Hold one the fins on the bottom of the agitator and remove the bolt. Remove the agitator. I would recommend ordering an new rubber washer and bolt. I did not, I removed the washer from the old agitator. Install the rubber washer and place the new agitator in the washer, tighten the bolt. Use some petroleum jelly to lube the rubber washer on the cover. Install the cover. Snaps in place. Install softener dispenser. Snaps in place. Test.

handy man did the repair and it took him about 15 -20 min when I order the part is was in the mail the next day very quick I like that susan I will use your store all the time.

I followed the instructional video step by step with additional patience.

Age and condition of the washer were unknown. I had no agitator grease available. I went for just the replacement of the Agitator Directional Cogs. I reviewed the video for replacing the whole kit. Removed fabric softener dispenser and the seal below. The seal needed to be cleaned. Removed the 7/16" bolt with a socket and extra long extension. Removed the agitator. Pulled off upper agitator. The part that holds the cogs is in about the center of the upper agitator. It also needed to be cleaned. One original cog was broken the other were past needing to be replaced. Replaced the cogs and the retainer. There was some effort with getting the upper agitator down far enough to re-install the bolt. That was just a slight alignment issue. The other parts were put back in place.