Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 7MMSL7959TW1

7MMSL7959TW1 Maytag Washer - Overview

Get Parts and Repair Help for 7MMSL7959TW1

If you know the washer repair part you need, you can browse the list of all parts on the 7MMSL7959TW1, or you can search by name or part description. You can also find your part by where it is located on the 7MMSL7959TW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 7MMSL7959TW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$25.37

Clutch Assembly

A worn clutch can cause a slower spin speed which will leave your clothes wet after a cycle. This clutch assembly comes with brake cam driver, blue spring for large capacity wash...

$5.11

Thrust Spacer

This white thrust spacer is made of plastic and is also commonly referred to as a retainer ring. It is used in the agitator assembly of many direct drive washing machine models. This is the retaining ring for inside of agitator. May need agitator grease for repair.

$11.30

Tub Wear Pads - Package of 3

This package of pads contains three brown tub wear pads.

$7.40

Leveling Spring

This spring is used on the leveling components in a washer. Please note, this spring may differ in appearance, but functions the same as original.

$14.02

Suspension Pads - Package of 3

$15.50

Tub-to-Pump Hose Kit

This kit comes with the clamps.

$7.22

Touch-Up Paint - White

18ml

$11.07

Spray Paint - 12 oz. - White

$11.05

Rear Leveling Foot

Sold Individually. Used to help stabilize the appliance on uneven surfaces.

$27.90

Oil Seal Kit for Gearcase Input Shaft

This two piece oil seal kit comes in two pieces and is used for the gearcase input shaft of your washer.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

spin cycle did not engage

  • Customer: Andrew from SLC, UT
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 313 of 334 people found this instruction helpful
researched potential causes, found cluch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly, removed agitator from inside the tub as it is connected to the gear shaft, turned washer on it's back for access to motor, unattached the direct drive water pump from the motor drive, unbolted the 3 gearcase... read more

Washer wouldn't run

  • Customer: Clint from Kansas City, KS
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 206 of 229 people found this instruction helpful
I removed the two screws on the back of the control panel. The control panel then flips back. The switch is on the left side. To remove the switch, I first detached the wire to the control panel and unscrewed the grounding wire. The new switch drops right in. I had a little trouble getting it in until I realized the washer lid had to be open. A little ... read more

Washer tub slammed into washer body during spin cycle

  • Customer: Brian from Seattle, WA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 167 of 184 people found this instruction helpful
If you load a washing machine unevenly, it will spin out of balance. But our washer seemed to make noise during the spin cycle regardless of how the load was distributed. I suspected that the suspension or balancing springs were getting tired, and ordered a replacement set.

First I disconnected the washer from the water and power supply, then I la... read more