Quick Question!

Have you ever purchased from PartSelect.com before?

Models > 7MMSL6955TW0 Maytag > Instructions

7MMSL6955TW0 Maytag Washer - Instructions

All installation instructions for 7MMSL6955TW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMSL6955TW0
76-90 of 225
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

clothes remain soaking wet after wash cycle

  • Customer: MICHAEL from lake elsinore, CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Wrench set
  • 2 of 3 people found this instruction helpful
The video was well made and made repair easy. I like the fact the video also showed how everything went back. The most difficult part and most time consuming for me was putting the washer cabinet or housing back on. I had a hard time lining the sides onto the slot to lock in place....the minor cut on finger sustained during the process was worth it. It saved me from buying a new washer and the whole family are happy that they don't have to wring out the clothes before putting it the dryer. Thank you!

Loud bang at the end of the spin cycle and symptoms of an unbalanced load.

  • Customer: mark from murfreesboro, TN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 2 of 4 people found this instruction helpful
After reading everyone elses stories, I purchased all new springs(5), new spring brackets(one of mine was rusted really badly)and all new wear pads(two sets of 3pcs each). The rusted spring bracket was the most time consuming as the screw was rusted into the bracked so I had to drill it out. Other than that, the actual spring replacement was easy. Took maybe 10 minutes. The wear pads were another story. I'm a pretty good mechanic and I had a bit of a struggle getting the old pads out. I used a long, flat head screwdriver to pry them out. Once they were out the new ones weren't too tough to get back in. Took about 20 minutes all together. I stongly recommend watching the video on removing the washer cabinet first. It will save you some time. Acutally, watch the videos on all of the parts to simplify the process. Oh and by the way, all of my washer problems are gone. Well worth my time and $70 in parts. Good web site!

the rubber lid seal had torn and was falling off of the lid.

  • Customer: VICKIE from MEQUON, WI
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
I removed the torn part which just pulled off of the lid and snapped in the new piece. No tools were needed. I also wanted to add that it was great doing business with Part Select. The part came well packaged, it came in a timely manner, and it was the correct part ! I will try Part Select for any of my future repair part needs.
Thank you

Agitator seperated from inside of wash drum

  • Customer: Larry from Brandon, FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

drum not turnig

  • Customer: Roy from Saint Peters, MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 1 of 2 people found this instruction helpful
I took the outside case off. took the bolt out of agitator, removed agitator, took motor out with ease of 2 scres and clamps, pulled trannny out and slidd clutch off and put new clutch on. replaced coupling while it was apart with new and better one for 12 bucks. put back together and works like new.......piece of cake........

Washer would not spin out with wet clothes in it.

  • Customer: robert from Fultonville, NY
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Remove top of aggitator, remove bolt 7/16 socket that holds aggitator to shaft. Pull aggitator out of machine. Tip machine on it's side. Remove 2 hoses connected to pump at end of motor. Remove 3 bolts holding gear box to tub frame (1/2" socket).Pull motor and gear box out from under machine. Note where washers, snap rings are on the shaft. Remove snap rings , slide clutch off shaft. Replace clutch , put back together.

water fill up but then stopped.

  • Customer: kathy from mccomb, MS
  • Difficulty: Really Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Socket set, Wrench (Adjustable)
  • 2 of 5 people found this instruction helpful
did not see how it was done husband and son put it together

Won't spin clothes properly. They were wet

  • Customer: Stanley from Santa Clarita, AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 2 of 5 people found this instruction helpful
Removed bolt from agitator assembly. Pulled up on the agitator vane and removed it.
tipped over macvhine . Drained water from tub via the drain hose assemble and removed clips from the hoses to the pump atached to the motor and drained residual water from the lines. Removed the electrical connector attached to the motor assembly and the three bolts holding the motor assembly and shaft to the tub and slid the shaft and assembry out.. Took digital photo of the assembly to insure proper part replacement and removed the clips and spring that are part of the assembly that holds on the clutch. Removed the old assembly and installed the new assembly . Installed the spring and retaining clip that came with the kit and installed the shaft . Installed the three bolts holding the/motor assembly and shaft in place and reconnected the hoses to the pump assembly and reconnected the electrical connector. Uprighted the washer and everything worked like new when I tested the spin cycle. I was quoted $225 to fix the bad clutch from the appliance tech that I paid $20 to diagnose the problem . Saved about $175 by doing it my self and it wasn't hard to do. My thanks to the previous persons that had done the repair and left iinstructions on how to do it.
SW Santa Clarita Ca.

lid gasket became older and brittle and eventually broke and cracked

  • Customer: kenneth from oregon city, OR
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Ordered the part and a couple of days later I popped off the old and popped on the new. It took longer to remove the part from the box than to install it.

The original seal on had deteriorated and was coming apart.

  • Customer: Sandra from Hamilton, NJ
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
Really nothing to it, especially since the original seal was coming apart. I just ripped it the rest of the way apart and removed it, then slid the new one on in its place.

Washer needed help to spin out

  • Customer: Timothy from Erie, PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 2 of 5 people found this instruction helpful
removed the old clutch assembly. Then replaced with the new clutch assembly and it works great.

tub would not spin

  • Customer: Greg from Dayton, OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Removed the agitator. Then removed the nut holding the agitator shaft. I set the machine on its side. Working from the bottom, i removed the three bolts which hold the transmission/motor. I removed the wiring. Pulling the unit down and out of the shaft bearing. The clutch assembly is on the transmission/motor unit shaft. Remove the snap ring and retaining ring for the shaft. Replace the clutch unit in the reverse order. The hardest part to replace is the retaining ring on the shaft. Pay close attention on how everything comes apart and you won't have any problems. Saved myself a lot of money.

Cracked, broken seal

  • Customer: Ronald from Glenwood, MD
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
The old seal had become brittle, cracked and fragmented and would no longer fit in the slot. Without it, washing had become a real mess. I took the new seal and snapped it in within a few seconds and was back up and running again. I looked everywhere for this seal, but this site was the only place I could find it. Thanks for having such a wide range of parts. This inexpensive broken part had made my machine unusuable. If it were not for you, I probably would have to resorted to a Sears appliance technician who would have charged $60 for just showing up.

rubber seal broke aprt

  • Customer: Lisa from North Attleboro, MA
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
slid the old seal off the lid and the new one popped on so easily
I do so many self- repairs at home now this was not even an issue.

rubber lid cushioning strip broke

  • Customer: Bruce from Hammett, ID
  • Difficulty: Really Easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 1 of 2 people found this instruction helpful
the original piece had 3 metal clips that held the strip in place. It was a matter of sliding the strip off and sliding the new replacement part on. Time involved was less than one minute. It took longer to find the part than to install it. The part was ordered Thursday night and it was installed by Monday! Great service!
All Instructions for the 7MMSL6955TW0
76-90 of 225