7MMSL6955TW0 Washer - Instructions

after watching the video of the part i repaired it was a breeze. the delivery of part was quick and it took a hole 20 minutes from start to finish replacing part and it work reall good now.all that was needeed was 7/16 socket with a long extention took longer to clean parts than to take apart and put back together.

After watching some on-line vids, I determined it was the center post, or tub, gasket at the bottom. A cheap part, and easy to snap-out the old and snap-in the new - But - I had to dissassemble the washer into individual washer component molecules. Luckily, I'd done this recently to replace the clutch drive, then the motor, then this. Not too bad, really. Washer body off (2 screws and two snap-links); agitator out (7/16" socket on extension); bang off tub nut (heavy hammer and punch); bang off drive block (hammer again); and pull tub up an out. Tub drain disconnected (pliers); pull off level sensing tube; three spring mounts (nutdriver); then just yank tub up. Poke out Centerpost gasket; snap in a new one; reassemble. Piece of cake.

followed on line direction. Great having access to a video on line to explain how to do the repair.

After a little research on line, I knew to remove the fabric softener cup, pull out the clear plastic divider, unscrew the agitator bolt, pop off the construction clips, slide a plate down a bit, remove the old cogs, put in the new, return all the pieces to their places, screw the bolt back in place and now it works perfectly. I also bought a cabinet clip, spacer & screw that I will use at a later date. This repair went quickly and easily.

From the central column, pull off the fabric softener dispenser (of course, with the machine off). Reach in and pull out the seal (looks like a diaphram). Using a socket, undo the bolt and pull out the plastic ratchet assembly. I found the 4 dogs in bad condition, ordered them, and received them in a couple days. Replace the old dogs and reassemble. Only the bolt requires a tool. Much simpler and cheaper than I had anticipated.

i did the repair by myself but based on the video that part repair provided me with.

Watched your video on line, was very easy to follow the instructions. I was very satisfied with your excellent service I received the parts within a couples of days.

replaced the agitator directional cap by simply removing the top of agitagor. unscrewing a bolt, slipprd off broken peice, slid new peice in place, and rescrewed it in. Voila washer runs and agitates as it should

After repair, had to re-align the front head of the cabinet several times to get it to slide in correctly.I saved myself the cost of a repair service call. Followed instructions at the following youtube.

Very easy - less than 30 min. Followed installation video available on PartSelect website, except did not have to disconnect all hoses or lay on back. Left washer in place all connected and raised up on blocks about 6" off floor. Removed cabinet as per video instructions. Changed pump as per video instructions. Video from website was crucial to easy repair. Would not have known how to release cabinet latches and remove cabinet without video. Cabinet was off in 3 min. and entire job was less than 30 min.

Videos made repair simple and easy.Only difficulty was re-installing cabinet.Hard to align.

Had a laptop with the repair video on next to washer and paused after each set of instructions to complete each task. Went perfectly! Only tricky part was fitting the cover back but eventually got it with a bit of jiggling. Very impressed with the instructional video as everything was where they showed it and came apart exactly as explained and more importantly went back together correctly.

I pried up the top timer setting box. Removed two screws on the back pried up the two clamps and disconected the door sensor. removed the outer case and removed the water pump. Put all the parts back on reverse order and was back in working order.

Watched the video on how to repair the problem and did what was instructed to do and the repair was that easy.

Removed control panel and rear panel replaced valve. Checked all grounds and connectors. Works like new.