Models > 7MMPS0070VM0 > Instructions

7MMPS0070VM0 Maytag Washer - Instructions

All installation instructions for 7MMPS0070VM0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMPS0070VM0
481-495 of 516
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Washer would not spin or agitate

  • Customer: John from Idaho City ID
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
1) Unplugged power to the machine. 2)Disconnected the water inlet hoses and the drain hose. 3)Placed the washer on the front of the cabinet. 4) Moved the washer to an area large enough to allow it to be laid down and worked on. 5)Removed the sound deading panel from the bottom of the washer. 6)Disconnected the electrical plugs from the motor. 7)Disconnected the two hoses to the pump. 8)Removed the two strap retaining bolts from top of the motor. 9) Removed the two motor retaining straps. 10) Removed motor and pump assembly from the transmission. 11) Removed the broken drive coupler and replaced it with the new coupler. 12)Reassembed in reverse order. Wish I had seen the brake repair vidieo before this repair was done. It shows how to remove the trasmission and motor asembley as a unit.

Screeching noise, would not drain at all.

  • Customer: Dave from Hermosa Beach CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Got on the PartSelect website and diagnosed the problem, purchased the replacement part, received the part in 2 days....very quick. I simply watched the "how to" video for the part, which was very easy to understand, and followed the instructions and was able to take out the old part (found it to be broken), replace it with the new part and fixed the washer. It took about 40 minutes, and everything works great. Easy, cheaper and faster than calling a repairman.

failure of agitation and spin, pump works

  • Customer: Max from Redmond WA
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
According to the video on your site with adaptation to the exact model. More time spent in removing/replacing the cover than any other part of the job

broken coupler between motor and transmission

  • Customer: gregorio from suamico WI
  • Difficulty: Really easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
I watch the video clip

plastic part of coupling was broken

  • Customer: Judith from Concrete WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers, Socket set, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
The new coupling parts are better made than the original parts. It was difficult to disassemble motor unit to get at the the old coupling, but once that was accomplished, the new coupling installed pretty easily. The machine is working fine now.

spin cycle did not engage

  • Customer: Lamar from Rochester MN
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set, Wrench set
  • 0 of 0 people found this instruction helpful
researched potential causes, found clutch dust under the washer and determined that it wouldn't engage because clutch was too worn. ordered the assembly,It was very easy to install. I also noticed oil residue on the side of the washer so after more research I found out I needed to replace the transmission also. The seal on top of the unit was worn out. I ordered a new transmission and install it and now it works like new. It's very rewarding to fix your own washer. Now all my friends are fixing their own washer and dryers. Thank You!!!

Fabric Softener Dispenser won't dispense softerner.

  • Customer: Rennel J from Rosamond CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 0 of 0 people found this instruction helpful
Very easy. Just snapped it on.

washer work not operate

  • Customer: William from Ballwin MO
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Unplug washer from the electrical receptacle. Remove one phillip screw on each side from the rear of the control panel and one hexnut with plastic strap from the rear of the control panel on each side. Pull control panel towards the front of the washer. Locate gray lid switch on the top left, rear side. Remove metal grounding screw with green wire from the metal top of the washer. Detach the gray lid switch from the electrical module and remove entire switch. At this time, open the washer machine lid carefully and gently install the new lid switch. Reattach the ground wire and metal screw to the chassis. Put control panel back in it's original location, carefully align each of the rear side phillip screws and tighten. Do the same with the two hex nuts and plastic strap. Close lid and remember to plug the washer back in to the electrical receptacle. Start the washer with your normal procedure! It should now start!!! Good luck!

Whirlpool washer pumps but drum would not spin

  • Customer: Roger from Granby CT
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
We have a 6 year old top loading Whirlpool washer. The drum would not spin at the end of its wash cycle when it is supposed to spin dry. I followed the video exactly and it worked great. I replaced the clutch and rubber coupling. It is not difficult if go slow and methodical and you follow the excellent video My wife washes heavy rugs often and it wore out the clutch. The washer works better than it has in a long time.

washer quit agitating & spinning

  • Customer: james from beverly hills FL
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Pliers, Socket set
  • 0 of 0 people found this instruction helpful
The repair was really simple. I loosened pump & hose .Removed old defective parts.Installed new parts which were 10 times better enginered than original ones. Thank you for your help & quality parts. Jim Merrick Crystal River Fla.

The unit would no longer spin in rinse mode etc.

  • Customer: Peter from Grinnell IA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Watched the video on your website and determined I could easily do the repair. Replaced the part for less than $20.00 including shipping and received it the next day. I ordered the part @ approximately 5 PM and the projected delivery was 1.8 days. To my delight the FedEx truck arrived by 1 PM the very next day and we were up and running within 24 hours of ordering the Direct Drive Motor Coupling. I will definitely use your services again. Special thanks to your video team. I was able to watch step by step how to disassemble and reassemble the washer etc.

When the machine was filling with water about 30% of it would miss the tub and run down the back of the machine and on to the floor.

  • Customer: Kenneth from Mahopac NY
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
After removing the front, sides and top of the machine (all one piece) the springs were relativley easy to access. I discover one of the brakets that held one of the springs had rusted and would no longer support the spring. I then replaced the bracket and springs. I Re-assyembled the machine and it work as good as new.

Washer quit agitating and spinning then after replacing the motor coupling it kept filling

  • Customer: Nathanial from Princeton MN
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
This is the first time I've ever fixed anything. I had no idea what I was doing but like the rest of you I decided to man up and get er done myself! I also didn't want to spend 200-300 bucks on a repair guy. So using this site and google. I figured out how to remove the back plate of my washer so I could correctly diagnose the problem...in fact I didnt' even have too remove the back plate to diagnose it because when I started to move the washer I found several broken plastic triangular pieces and a round rubber piece with 6 triangular holes in it. On one of the broken pieces was a serial number of some sort. So I googled what i found and matched what i found on underneath my machine with a part i found on this website which turned out to be the direct drive motor coupling...i figured i was in for a rough battle with the machine but it actually turned out to be pretty easy...in fact it would've been easier had this machine not been serviced before in the past...(i'll get to that later) first step was to remove the back plate...using youtube i figured out how to remove the metal clamps that hold the cabinet to the back plate (you will need a flat head screw driver). Rest was elementary it took me about 2 minutes to remove the back plate after spending probably 30 minutes of research online (i like to make sure i'm doing everything correctly so i watch several videos and do a ton of reading before i mess with anything)*also a side note make sure you unplug the machine before you do anything! Also turn off the water and remove the draining tubes from the back of the machine because you will need to tilt the whole thing on its back failure to do this will result in a watery mess and u could kink the drain tube which will lengthen your repair time like it did with me. Also remove the hot and cold water tubes from teh back...remember that the hot water is always on the bottom memorize where you put the tubes...u can always check which is which by turning the water back on but it will save you sometime* once i got the back plate off i tilted the machine on its back so i could get to the motor and the water pump...there are 2 metal clamps that hold the water pump to the motor. All it takes is a flat head screw driver to remove these clamps once you get the 2 clamps off you can lift the water pump right off the motor its really easy. This exposes the motor which houses the direct drive motor coupling. I inspected what was left of the coupling and if there was any doubt that it was the motor coupling there wasn't anymore because it was clearly broken and the rubber piece that was supposed to sit between the 2 plastic things was gone. Needless to say it was a mess and i knew it was gonna be a challenge to remove the broken coupling. It was surprisingly easy to remove the coupling from the top of the motor compared to the middle of it. There are 2 more metal clamps that fasten the motor in place so it doesn't move around...there are 2 screws that hold these clamps in place. I removed one of them with no problem but the other one was stripped extremely bad i was completely unable to remove it. If you are in this bad boat like i was in i have a solution for you...you only need to remove one screw if you can grab the motor and rotate it enough u can remove the clamp from the metal plate without ever having to remove the clamp at all...its a little difficult and you will have to use a bit of elbow grease to do it but it can be done. Once i achieved this it was a lot easier to access the broken coupling from the middle of the motor. I took the back end of a hammer and evenly jiggled the coupling loose until it popped off...it took a solid 10 minutes tho since the coupling had shattered so bad there wasn't much for the hammer to hold onto. Once i did this i was able to get the new pieces in place...it was a little tricky to line things up correctly but after awhile i was able to get it to fit perfectly...I put the machine back

No aggitator or tub drive

  • Customer: Mark from Walker LA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I did like the video said about the removal of the control pnl. Now removal of the of the top and front cover was a bit more of a learn as you go to remove all the hoses that go to the fabrix sofner, bleach, and detergent compartments. It was done with the aid of a pair of pliers. There was 4 lines in the top at the back left that has to be removed to finish the cover removal! Now after that it was easy. the rest was like the video. Motor and pump removal simple. I would remember to inspect the inside of the pump to remove any trash that might get wrapped on the impeller.less than hour start to finish and it was a cheap fox and better than buying a new washer!

lid switch has burned out (actually melted) and the washer would no longer agitate

  • Customer: keith from vernon CT
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
removed the two screws from the back of the dial bar on the top of the washer. removed original unit, and install the new unit.
All Instructions for the 7MMPS0070VM0
481-495 of 516