Models > 7MMMS0100VW0 > Instructions

7MMMS0100VW0 Maytag Washer - Instructions

All installation instructions for 7MMMS0100VW0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the washer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMMS0100VW0
76-90 of 205
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

tub would not spin

  • Customer: Greg from Dayton OH
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
Removed the agitator. Then removed the nut holding the agitator shaft. I set the machine on its side. Working from the bottom, i removed the three bolts which hold the transmission/motor. I removed the wiring. Pulling the unit down and out of the shaft bearing. The clutch assembly is on the transmission/motor unit shaft. Remove the snap ring and retaining ring for the shaft. Replace the clutch unit in the reverse order. The hardest part to replace is the retaining ring on the shaft. Pay close attention on how everything comes apart and you won't have any problems. Saved myself a lot of money.

drum not turnig

  • Customer: Roy from Saint Peters MO
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 1 of 1 people found this instruction helpful
I took the outside case off. took the bolt out of agitator, removed agitator, took motor out with ease of 2 scres and clamps, pulled trannny out and slidd clutch off and put new clutch on. replaced coupling while it was apart with new and better one for 12 bucks. put back together and works like new.......piece of cake........

Agitator seperated from inside of wash drum

  • Customer: Larry from Brandon FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Socket set
  • 1 of 1 people found this instruction helpful
I had to find a point of reference first since item came apart in wash cycle and internal pieces fell out - thank goodness for YOUTUBE. Another guy was thoughtful enough to do a video on how the assembly came apart / went back together - a huge help for sure. Actual repair was less than a half hour after obtaining new part and seeing video. The 12 year old washer works like brand new - saving me close to 1,000 dollar replacement charges.

Won't spin clothes properly. They were wet

  • Customer: Stanley from Santa Clarita AL
  • Difficulty: Easy
  • Time to Complete: 1- 2 hours
  • Tools Required: Socket set
  • 2 of 4 people found this instruction helpful
Removed bolt from agitator assembly. Pulled up on the agitator vane and removed it.
tipped over macvhine . Drained water from tub via the drain hose assemble and removed clips from the hoses to the pump atached to the motor and drained residual water from the lines. Removed the electrical connector attached to the motor assembly and the three bolts holding the motor assembly and shaft to the tub and slid the shaft and assembry out.. Took digital photo of the assembly to insure proper part replacement and removed the clips and spring that are part of the assembly that holds on the clutch. Removed the old assembly and installed the new assembly . Installed the spring and retaining clip that came with the kit and installed the shaft . Installed the three bolts holding the/motor assembly and shaft in place and reconnected the hoses to the pump assembly and reconnected the electrical connector. Uprighted the washer and everything worked like new when I tested the spin cycle. I was quoted $225 to fix the bad clutch from the appliance tech that I paid $20 to diagnose the problem . Saved about $175 by doing it my self and it wasn't hard to do. My thanks to the previous persons that had done the repair and left iinstructions on how to do it.
SW Santa Clarita Ca.

washer shakes and was very noisey

  • Customer: william from lindside WV
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 2 of 4 people found this instruction helpful
researched the problem from the web-site.found the three most common things that would cause the problem.inspected the washer to see if there was evidence that one of the described parts had falled,and found that the tub wear pads were missing do to wear.simply replaced and it solved the problem. Thanks for the information.

pipe had a hole

  • Customer: eddie from lockesburg AR
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 2 of 4 people found this instruction helpful
I pulled the hose off and notice their was a part # and I went online and type the part # and showed the part and cost. I order it and receive it within 3days. when the part arrive I replace the hose in minutes. If I can do so can you its that easy.

Washer would do nothing

  • Customer: Joel from Tompkinsville KY
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Pliers, Screw drivers
  • 2 of 4 people found this instruction helpful
I never have and never will claim to be a mechanic. my wife said it had to be the lid switch. After opening and closing the lid I agreed. Took 2 screws out of back of top panel lifted control panel out of way and there was the lid switch just as part select custumers had said. $100 repairman fix, and I fixed it for a little over $20.

would intermittently fail to spin during rinse cycle

  • Customer: Robert from Covington WA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 1 of 2 people found this instruction helpful
Watch the video. Remove agitator. Disconnect power and water supplies. Lay machine on its back. Unclip and move pump out of the way. Remove three bolts securing motor assy. Slide motor assy and agitator shaft away from tub. Remove a washer and c-clip to slide clutch assy off of shaft. Install new clutch and reassemble machine. Total time to repair is about 30 minutes.

Washer needed help to spin out

  • Customer: Timothy from Erie PA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set, Wrench set
  • 1 of 3 people found this instruction helpful
removed the old clutch assembly. Then replaced with the new clutch assembly and it works great.

Both outside door handles turned very beige

  • Customer: Howard from Boynton Beach FL
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 5 of 15 people found this instruction helpful
Everything worked perfectly---thanks to the suggestion of your call center agent. She suggested that since the replacement door handles were no longer available, I should consider repainting them--it worked like a charm. Please tell her she was a life saver. We rent that house in Fl and my returning tenants had complained about the discoloring refer handles. Thank you

washer would not spin

  • Customer: Tim from Shermans Dale PA
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Watched video instructions and replaced the clutch like I've been doing it for years. The repair took about 30 minutes. The video was extremely helpful !!!!

The washer was slow would not go into the spin cycle..

  • Customer: John from Burbank CA
  • Difficulty: Easy
  • Time to Complete: More than 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
All I had to do was follow the instructions on your web site and it was pretty easy.. The only reason it took so long was because my washer is in a spot hard to get to... I had to remove the dryer to get to the washer and then take it out of the laundry room to work on it. Other than the time it took to do that the actual repair only took 40 minutes. Your video of the repair was excellent... Thanks so much.. Saved at least $500 by replacing the clutch...

During the spin cycle machine rocks the house

  • Customer: Norman from Burlington NJ
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
Replaced all of the springs. I put the shell back on and the problem still exists. I thought $20.00 was worth seeing if this would resolve the issue. I don't want to keep throwing parts at it. I noticed some black suit under the machine. I will be buying a new washer.

Washer doesn't spin

  • Customer: Chuck from Gig Harbor WA
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Socket set
  • 0 of 1 people found this instruction helpful
The hardest part was figuring out what the problem was. The washer wouldn't spin so the clothes were really wet at the end of the cycle.
First I removed the agitator, because a screw connects the agitator to the shaft.
Next I put the washer on it's front.
Disconnected the water pump clips and pulled it off the motor shaft.
Electrically disconnected the motor (make sure you unplug the washer before starting)
Removed 3 bolts holding the gear case and motor.
Then I pulled the gear case and motor out the bottom, the shaft is about two feet long and the clutch comes with it.
Replace the clutch and put the shaft back where it belongs. Make sure the clutch spring doesn't bump against the plastic brake thing, it will stop you from pushing the shaft all the way in.
Pushing the gear case and motor assy the last inch and aligning the holes for the bolts was the hardest part. The bolts aren't long enough to grab the threaded hole, so you have to get it perfectly aligned. After about a half-hour of fighting it, I finally used a hammer and lightly tapped it into place.
Just put everything back together in the reverse order.

Tub out of balance on spin cycle. Very Noisy!

  • Customer: Stacy from Markle IN
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers
  • 0 of 1 people found this instruction helpful
I the took washer to where I could lay it on its side.
Laying it on its side lets the suspension spring at the top go slack. Making pulling it from bracket easier.
Next , I lifted the tub up with a 2x4 and blocked it with another wood block. This let me have slack in the lower springs.
Of coarse I saved the hardest one (behind the motor) for last. I only swore a little! But got it to come out.
By the way, put in each new spring, before going on to the next one.
The new springs helped a lot, but I ended up ordering the wear pads a day or two later. They were very easy to replace. Just pop the old ones out of the frame with a screw driver. then pop the new ones back into the holes and you are done.
You may just want to buy them both and do it all at once. Saving moving the washer twice!
All Instructions for the 7MMMS0100VW0
76-90 of 205