7MMGP0070VM0 Maytag Dryer - Instructions

According to your site, we purchased the Door Switch and the Thermal Fuse as these two parts had the highest percent of "what could be wrong". Figured we would send one back if we didn't use it. The Door Switch was replaced first and the dryer worked! Two days later, the dryer stopped working again. Still had the Thermal Fuse so we changed that out. The dryer worked again! Both parts arrived sooner than excepted! Both parts were simple to replace! The diagrams were very handy. The picture of the parts assisted greatly and the video's were the icing on the cake! VERY glad that we ordered both! Will recommend to everyone! PartSelect is bookmarked should we ever need your assistance in the future!

Exactly as described in the video provided online. Couldn't have been easier to do. All businesses should supply their customers with this kind of repair option!

I watched your video online. And followed those instructions. It made it very intuitive and practical to follow. Believe me I am a novice but you made me feel like I am a professional.Thanks.

We bought a slightly used dryer, which kept running when the door was open. Trying to get the lid off, I broke one of the clips that held the top on. I gave up, and went to the internet. PartSelect made it easy to find my model and a list of all of the parts. They also had an on-line video that showed me the location of the secret screws that I couldn't find that led me to breaking the clip. After watching the video, the job was insanely easy! I was also surprised that their web site estimated the delivery of the parts at 1.8 days. I figured that this was an average, but the parts actually showed up at my door 1.8 days after I ordered them!

I followed watched the part select videos on U-Tube and then made the repair. Anyone mechanically inclined should have no problem making repair. Removed the back panel then removed the front panel and drum. Replaced thermostat in rear of the dryer than moved to the front and replaced the two gas valve coils vacuumed out the lint reassembled tested. Dryer worked fine.. I believe the only thing that needed replaced was the thermostat but, replaced all three.

Disassembled entire unit, vacuumed out all the lint & dust.Removed beater bars from drum and cleaned. Removed old / broken igniter replaced belt. Re assembled.

unhinged top panel. removed front panel. installed belt and reinstalled front and top panel.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

open machine up and replaced the new belt.

removed frt cover & drum, replaced solenoids, cleaned the unit interior

1. Opened the top. (UN-plugged it first) by prying between top and front of machine.
2. Disconnected the door switch
3. Removed two screws one each on top corners of front
4. Pulled top of front cover forward and lifted up to remove.
5. The drum will fallout if not careful, good time to remove drum to clean dust from inside machine.
6. With drum in place slide new belt, skinny side down around drum, to about halve way back.
7. While supporting drum reach back to the motor area, should be on right side facing front of machine. There you will find the belt idler/tension assembly.
8. Thread the belt through the assembly and around the motor drive pulley.
9. Ensure the tensioning assembly is firmly in the slots on floor of machine.
10. Reassemble housing in reverse order. took about 45 minutes

I watched the video to know how to change the belt. I removed the front panel and slid the belt over the tub (you will have to pick the tub up a little). Then I reached around with one hand and slid the belt over the pulley. Then I used the same one hand to push the tensioner back and slip the belt behind it. You will be doing most of the work by feeling not by vision but that's where their video is helpful. I paused the screen on my laptop where it shows how the tensioner goes around the belt. Also when you slide the belt over the tub look for the grove the previous belt left for alignment. It took me 10 minutes.

Opened the bottom panel w/ 1/4 nut driver to access the flame sensor and easy fix.

Exactly as hown in your video. No problem.

it took longer to diagnos the problem than to fix it