7MMGL6741TW1 Maytag Dryer - Instructions

Watched the how to video on the parts select site. The job to replace the motor was easy although I had some issues with the blower fan wheel as it is made of plastic and was frozen to the motor, yes I turned it the correct way for the left hand threads. I ended up distroying the blower fan wheel and had to buy a new one. I had to remove the rear plate to get at the fan component, but thta was easy to do also. This site should add a "Sometimes bought together" comment for the motor replacement. After all was done I read some of the other comments and found some others had the same problem with the fan wheel. Once I had all the parts the dryer went back together fairly quickly. The job was easy to do and I would believe almost anyone could do it.

DISCONNECT dryer from power source. Removed 2 screws holding lint filter housing, pulled top cover forward to release the two plastic keepers, raised the top cover. Disconnected two wires from the door switch, removed two screws holding front pannel assembly, slightly raised off of two hooks and removed. Supported drum by placing a strap from one side top under drum to the other side top. Removed broken belt. Vacuume any lint from under and around drum. Slid new belt over drum, under drum stuck folded end of belt through tensioner and on to motor pulley. Reinstalled front pannel assembly by lowering onto two hooks near bottom, removed support strap, reinstalled the two screws, hooked up wirind to door switch, lowerew top back in place inserted two screws back into lint filter housing. Plugged up to power supply. Test operate.

According to your site, we purchased the Door Switch and the Thermal Fuse as these two parts had the highest percent of "what could be wrong". Figured we would send one back if we didn't use it. The Door Switch was replaced first and the dryer worked! Two days later, the dryer stopped working again. Still had the Thermal Fuse so we changed that out. The dryer worked again! Both parts arrived sooner than excepted! Both parts were simple to replace! The diagrams were very handy. The picture of the parts assisted greatly and the video's were the icing on the cake! VERY glad that we ordered both! Will recommend to everyone! PartSelect is bookmarked should we ever need your assistance in the future!

Exactly as described in the video provided online. Couldn't have been easier to do. All businesses should supply their customers with this kind of repair option!

I watched your video online. And followed those instructions. It made it very intuitive and practical to follow. Believe me I am a novice but you made me feel like I am a professional.Thanks.

We bought a slightly used dryer, which kept running when the door was open. Trying to get the lid off, I broke one of the clips that held the top on. I gave up, and went to the internet. PartSelect made it easy to find my model and a list of all of the parts. They also had an on-line video that showed me the location of the secret screws that I couldn't find that led me to breaking the clip. After watching the video, the job was insanely easy! I was also surprised that their web site estimated the delivery of the parts at 1.8 days. I figured that this was an average, but the parts actually showed up at my door 1.8 days after I ordered them!

Disassembled entire unit, vacuumed out all the lint & dust.Removed beater bars from drum and cleaned. Removed old / broken igniter replaced belt. Re assembled.

unhinged top panel. removed front panel. installed belt and reinstalled front and top panel.

Replaced the flame sensor since it was believed to be the problem contributing to the lack of flame in this gas dryer. However, this part did not correct the problem.

open machine up and replaced the new belt.

removed frt cover & drum, replaced solenoids, cleaned the unit interior

It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

just took off the front panel took off the belt and replaced it with the new one we watched the video pretty easy

Raised top of dryer and removed screws holing front on. slid front panel up and off to remove drum. Seal was easy to install but you do have to be careful with the adhesive. After adhesive was dry laid dryer on it's back and installed drum. Reinstalled drum belt. Placed front panel back on and installed the two screws holding it in place. Set dryer upright and closed top.

Easy, screw driver (flathead) popped up two clamps on each side of top. maybe 3" from each side. Propped lid up with I think I used a full roll of paper towels, part was inside top left, unscrewed old,used small hook tool to unplug old, put new checked to see if it worked and bang lower top pop in place.NOTE : I am pretty good with fixing little things like this.. PLease UNPLUG for safety first then take time and be happy when you save $ on doing it yourself.