All Installation Instructions for Maytag Dryer 7MMGD6630TQ1

would not heat

changed fuse,radiant flame sensor. no help. bought a new dryer. i don't think the gas valuve was opening.everything seemed to be working properly,just no gas.

Parts Used:

Dryer Radiant Flame Sensor

marc from bristol, WI
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Broken Belt

PartSelect sent the exact right part, and very quickly! YouTube showed me how to install it. The only hard part was the bulkiness of the drum, which is why I marked "a bit difficult" for the repair.

Parts Used:

Multi Rib Belt - 92-1/4"

Patricia from Durham, NC
Difficulty Level:
A Bit Difficult
Total Repair Time:
30 - 60 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

The ignitor would lite, but no gas from the valve, then ignitor would shut off

It was a fairly simple repair to perform with the dryer in place. I simply opened the bottom/front access panel to start, the door removes if you pull up after opening. Then I disconnected the two and three wire connector to the two coils. Next I removed the bracket screws that fasten the coils to the valve assembly. This was a little difficult with the screw closest, because of the small clearance and #1 sized phillips(stubby would work well.) The rear screw I managed to remove by using both a small flathead screwdriver(hex shaped shaft) and an adjustable cresent wrench. At this point, it was a simple matter of installing the new coils and the bracket, and then reconnecting the two plugs. It almost made me want to do laundry.

Parts Used:

M Series New Style Coil Kit

Lee from Madisonville, KY
Difficulty Level:
A Bit Difficult
Total Repair Time:
Less than 15 mins
Tools:
Screw drivers, Wrench (Adjustable)

Was this instruction helpful to you?

Thank you for voting!

Lint filter handle broke

Slid the new lint filter into slot on top of my 26 year-old Kenmore dryer and it fit perfectly! Ordered part and received it the next day...unbelievable!! Definitely A+ service.

Parts Used:

Lint Filter

Joan from Dudley, MA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

It woud begin to heat and dry clothes then it would stop heating before the clothe dried.

Parts Select said 27% chance it was the coils and 26% chance it was moisture sensor. I ordered the coils and it did not fix the problem, my luck. I have now ordered moisture sensor and the next possible part, the cycling thermostat. If one of these solve the problem I will still have much less invested than a repairman would charge.

Parts Used:

M Series New Style Coil Kit

Thomas from Bath, NC
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer would heat up at startup but not stay hot for long. Took forever to dry clothes. Started smelling a very slight gas leak about a week before the problem started. I suspect the coils have been going lame for quite some time. The dryer heats up like it was new.

Downloaded a schematic of the dryer controls. Watched a UTUBE video of how to remove the front panel of a Maytag Performa dryer. It was pretty easy. Consulted your website and found out that bad coils are typical of the symptoms 46% of the time. I have bought parts from you before and happy with results.

Parts Used:

M Series New Style Coil Kit

dan from Orinda, CA
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken door catch: female half

noticed that male half was in good working order, so I just snapped in the new female half; without any tools. easy repair!

Parts Used:

Door Catch Kit

Allen from Seattle, WA
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

flame out

easy as pie !

Parts Used:

M Series New Style Coil Kit

john from glen head, NY
Difficulty Level:
Really Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Pliers, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Dryer worked but did not heat

Followed troubleshooting steps. Checked thermal fuse (shorted)- OK. Checked igniter (about 70 ohms) - OK. checked flame sensor - (open) BAD (should read shorted). This part is normally shorted then opens when the igniter gets hot causing it to open and thus turns on the gas flow. An open flame sensor does not permit the igniter to turn on.

Parts Used:

Dryer Radiant Flame Sensor

Steven from Garden City, NY
Difficulty Level:
Easy
Total Repair Time:
30 - 60 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

broken belt

the video was very helpful

Parts Used:

Multi Rib Belt - 92-1/4"

Robert from Winchester, IN
Difficulty Level:
Easy
Total Repair Time:
15 - 30 mins
Tools:
Nutdriver, Screw drivers

Was this instruction helpful to you?

Thank you for voting!

Replaced lint filter

The part was delivered when promised. Part was a perfect fit. I was very pleased with the entire process.

Parts Used:

Lint Filter

Robert from Palatka, FL
Difficulty Level:
Really Easy
Total Repair Time:
Less than 15 mins

Was this instruction helpful to you?

Thank you for voting!

Won't tumble

Watched how-to video provided on PartSelect website. Most time was spent cleaning out the cabinet of lint and other debris. I found over 5 bucks in loose change! I Found pulling the belt over the motor pulley to be the trickiest. Note: my dryer will be 30 years old come this September. I wonder how many more years I'll get out of it!

Parts Used:

Multi Rib Belt - 92-1/4"