7MMGD6630TQ0 Maytag Dryer - Instructions

watched the video and it couldn't have been easier

a salesman from sears told me that all i had to do was take putty knife to pry dryer top off .I found piece and unplugged broken piece, which was hardest thing to do and plugged new piece in and put the screws back in dryer.There was also video online that made it very simple. I am very grateful to salesman because he saved me lots of money.

My husband who is in a wheelchair and his freind who had never worked on a dryer,watched the video online and boom! just like that it was fixed!Some nut told me it would cost too much to fix,To just get a new one!Boy am I grateful for you!Thank You.virginia.

First and foremost, PartSelect is awesome! I placed the order on a Monday afternoon with regular shipping, and I had the belt Tuesday evening. Total repair involved removing several screws to open the top and front of the dryer, then installing the new belt. Pay close attention to the the dryer seal - make sure this is completely set. This was a very, very easy repair, and it cost me less than $20 for part and shipping! Also, the video on the PartSelect site shows exactly how to make this repair, and was very helpful.

In accordance with supplied video and instructions. Special note - watch out for sharp edges on the dryer panels!

We only had to tilt the dryer enough to be able to screw the leveling leg in place.The only hard part was holding the dryer steady to screw in the leveling foot.

Removed 2 screws at filter vent on top of dryer Remove screen. Take screwdriver & pry up lid at 2 front corners. Lift lid. 2 more screws inside top front corners.Remove screws. remove front panel.wrap belt around tub. Take cup or can to hold tub in place level.Thread belt around tentioner pulley & motor shaft Look at directions very closely to figure out how to thread belt. read at least 5 times.LOL Reinstall & you are through.PS you can see where old belt rode so try to line up as close to track as possible. Guy

You have to disassemble the dryer. I looked up how to on youtube.com. I am grateful that people take the time to record the steps in which to do just about anything. Disassembled and ordered motor and fan, damaged fan taking it off, got it in in just a couple of days, installed motor, fan and drum, tested before complete assembly. Works great. Thanks

Followed Directions included with Kit. Directions were right on. Have done other Range and Drier conversions in the past.

replaced belt

Watched video on the website and saw how easy it was so ordered the part. Part arrived quickly and had dryer up and running within 15 minutes. Good part good price and good intructional video

Fortunately this is an easy diagnosis and easy repair. The great PartSelect instructional videos are a HUGE HELP!!

Goggle the make and model and videos were available on how to remove the lid. I would not have know how to otherwise.

First unplug the unit and move to an area where you will have enough room to pull the drum out. I opened the top by sliding a screwdriver in the top left and right edge and popping the clips to allow the top to lean up and back against the wall. I tried to unclip the harness for the door switch but couldn't get the harness to release and instead took out the two screws holding the door switch in place. This is located on the top right inside the dryer door. Once the switch was off I was able to use the socketdriver to undo the two screws on the inside top left and right to release the front of the dryer by pulling up easily and unhooking the bottom front. I was then able to set the front of the dryer aside and begin removing the belt from the tension wheel and motor. Pay close attention to how the two are connected because it will confuse you putting it back together.The belt feeds through the tension wheel and when you release it the tension wheel is just sitting in place and may pop out of place. Remember which slots it sets back into for when you put the dryer back together. We removed the drum, checked the two rollers to make sure they were in good working order. I removed quite a bit of debris from them. Once the drum was out I pulled off the old seal. Took a piece of sandpaper to rub away any excess old adhesive and began installing the new felt seal. Follow the directions carefully to ensure that the seal is sitting on the edge properly before you begin applying adhesive under the edge. I had someone helping me to install the seal but probably would have needed clamps to hold the seal while working it on. It's not a super tight fit but is fitted and once you start putting it on it easily slips off the other side. A couple clamps would hold it in place if you don't have someone to help. Once the seal is on and you apply the adhesive you begin putting the drum back into place first by slipping the belt back over the drum where it can hang until you are ready to put it back on the motor. You have to make sure the seal isn't folded under the back of the dryer. Again a little tricky but if you gently spin the drum slowly counter clockwise a few times you can work it so it's not folded under. Once you see everything is in place you can reconnect the belt through the tension wheel onto the motor. Check drum again by spinning counter clockwise. Install the front of the dryer back on by setting it into the bottom clips. Put the top screws back in. Re-install the door switch making sure it's back in place with the tab sticking through the hole at the top of the dryer door. Bring the top back down. Close the dryer door and plug it back in and everything should be good to go. It wasn't a difficult job at all and I would probably attempt other repairs now that I've done this one. Beware the adhesive is kind of watery when it comes out but you don't need to use a lot under the edge of the seal. Good luck with your repair. I am thankful that PartSelect was so easy to order my parts from and I got the part within a few days. Thanks!

Followed the instructions that came with belt everthing went just fine.