Models > 7MMGD6630TQ0 > Instructions

7MMGD6630TQ0 Maytag Dryer - Instructions

All installation instructions for 7MMGD6630TQ0 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dryer repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7MMGD6630TQ0
511-525 of 899
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Drum not turning, belt broken

  • Customer: Franklin from Midway WV
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
DISCONNECT dryer from power source. Removed 2 screws holding lint filter housing, pulled top cover forward to release the two plastic keepers, raised the top cover. Disconnected two wires from the door switch, removed two screws holding front pannel assembly, slightly raised off of two hooks and removed. Supported drum by placing a strap from one side top under drum to the other side top. Removed broken belt. Vacuume any lint from under and around drum. Slid new belt over drum, under drum stuck folded end of belt through tensioner and on to motor pulley. Reinstalled front pannel assembly by lowering onto two hooks near bottom, removed support strap, reinstalled the two screws, hooked up wirind to door switch, lowerew top back in place inserted two screws back into lint filter housing. Plugged up to power supply. Test operate.

Dryer wouldn't turn on.

  • Customer: Barbara from Lake Mary FL
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
According to your site, we purchased the Door Switch and the Thermal Fuse as these two parts had the highest percent of "what could be wrong". Figured we would send one back if we didn't use it. The Door Switch was replaced first and the dryer worked! Two days later, the dryer stopped working again. Still had the Thermal Fuse so we changed that out. The dryer worked again! Both parts arrived sooner than excepted! Both parts were simple to replace! The diagrams were very handy. The picture of the parts assisted greatly and the video's were the icing on the cake! VERY glad that we ordered both! Will recommend to everyone! PartSelect is bookmarked should we ever need your assistance in the future!

Dryer started making a squeeking noise and would shut off after only 3-4 minutes of drying.

  • Customer: David from Goodyear AZ
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench set
  • 0 of 0 people found this instruction helpful
It is a washer/dryer combo. First I unplugged the unit. I had to remove the top and front of the dryer, remove the belt and remove the drum. I then removed the side panel that the motor was on. That was a little tricky getting at a couple of the screws. I then took the flywheel off which was somewhat difficult. It screws off in the opposite direction and was hard to get loose. I unplugged the motor, no wires to connect. There is a clip on the front and back of the motor holding it in place. Take them off and the motor comes right out. Replace the new motor and screw the flywheel back on. Install the clips, plug the motor in and put everything back as you took it apart.

belt broke

  • Customer: Debra from Columbus OH
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
just took off the front panel took off the belt and replaced it with the new one we watched the video pretty easy

Drum seal came apart

  • Customer: Glen from El Paso TX
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Screw drivers, Socket set
  • 0 of 0 people found this instruction helpful
Raised top of dryer and removed screws holing front on. slid front panel up and off to remove drum. Seal was easy to install but you do have to be careful with the adhesive. After adhesive was dry laid dryer on it's back and installed drum. Reinstalled drum belt. Placed front panel back on and installed the two screws holding it in place. Set dryer upright and closed top.

door switch

  • Customer: John from Austin TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
Easy, screw driver (flathead) popped up two clamps on each side of top. maybe 3" from each side. Propped lid up with I think I used a full roll of paper towels, part was inside top left, unscrewed old,used small hook tool to unplug old, put new checked to see if it worked and bang lower top pop in place.NOTE : I am pretty good with fixing little things like this.. PLease UNPLUG for safety first then take time and be happy when you save $ on doing it yourself.

Dryer would heat, initially, but would not come back on

  • Customer: Kevin from BRAINTREE MA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
My suggestion is to read all of the items that may result in no heat, or insufficient heat, you will find your problem in one of the reply's and the right part to replace. The repair was made much easier, as I installed a Maintenance kit at the same time. Drum rollers, drive belts and tensioner. With the drum out, the coil retaining clip was a LOT easier to re-instal. If the drum isn't out, you can lift the drum up a little and squeeze a stubby screw driver in to loosen the retaining screws. You have to use the proper size screwdriver so you don't strip the screws, and maybe a pair of gas pliers around the handle of the screwdriver to give it a little torque to help loosen the screws, while keeping downward pressure on the screwdriver.

Lint Chute and Lint Trap Seals had Deteriorated

  • Customer: Robert from Melbourne FL
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
The on-line instructions were excellent; however, the man doing the demonstration used a brand new machine - not one where the old seals had melted and dried out and required serious cleaning before attaching the new seals. The new seals went on easily and I am very happy with everything about this task. I am also glad I now know what that lint chute looks like, so I'll do a better job of keeping it clean in the future.

Dryer wouldn't start.

  • Customer: Linda from Panama City FL
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Screw drivers
  • 0 of 0 people found this instruction helpful
I watched the video multiple times until I was comfortable. He made it look so easy. I'm convinced the dryer was using had been "prepped" to come apart and go back together easily. The reality for me: Great difficulty popping the cabinet top. It took every ounce of power to push in the hinges. Disconnecting the existing switch was difficult. I depressed in the catches on each side, but of course one at a time since I only have two hands. I tried various rigs to get both pushed in at once - nothing. Finally I watched a different vendor's video and the technique he used worked for me. Lastly, screwing in the new part is darn near impossible upside down to screw it in straight. The screws also wouldn't go in flush with the surface. I got them in well enough to hold, but that's it. The good news, the choice of part was correct and it fixed the problem. Had it now, I would have gone to Plan B and ordered a different part and paid another $9 shipping on top of the part. In my next life, I'm going to marry a appliance repairman.

The dryer does not heat

  • Customer: Diana from Nassau Bay TX
  • Difficulty: Really easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers, Wrench(Adjustable)
  • 0 of 0 people found this instruction helpful
I just knew it had to be the heat sensor unable to activate the actual ignition. I following the directions and video for the installation of the heat sensor #PS344761. It went very smoothly. Upon completion of the installation, the click, then the flame roared to life and I felt like a real do-it-selfer!! This was short lived. The wetness of the clothes had no effect. Something I did not do and I certainly know better was to check and see what was taking place before I replaced the "damaged" sensor. No, I was just so sure there was no need of that. You say, put the old back in and watch what happens....I recycled the old one immediately. Sigh! We have had two weeks of rain and I'm really tired of damp clothes everywhere. I will read other alternatives and report back. DClark, TX

Dryer belt broke

  • Customer: John from Lexington NC
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver
  • 0 of 0 people found this instruction helpful
Pulled up a You-Tube vid on how to install the belt. Went perfect.

Door Switch broke

  • Customer: MONICA from DUBLIN GA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers
  • 0 of 0 people found this instruction helpful
I pulled up the "How To" on the internet and it gave me step by step instructions. I only had to deal with 4 screws. Yaaayy! It was a good experience and the piece was perfect.

the clothes drum stopped turning

  • Customer: Joseph from E.Northport NY
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
i first watched a video on U-Tube and did exactly as they did. removed screws from the lint tray, pried up the top panel of the dryer with my putty knife, unscrewed the 2 hex screws at the top, disconnected the plug for the dryer door,and installed the new belt it really was pretty easy. the only thing I would recomend would be when installing the belt put towel or anything that would protect your arm from the botttom piece of sheet metal. I got a pretty good cut on my forearm while I was putting the belt on the bottom pully.

Would not heat clothes dry

  • Customer: rick from Burton MI
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
unplugged dryer and removed front panel. removed the screw that holds flame sensor and unplugged electrical wires. then replaced with new. Did not solve problem so I ordered the replacement coil kit and installed them using phillips screw driver and this solved problem. Dryer is working fine now. I found this site very helpful and would recommend it to a friend.

not enough heat from gas dryer, would do one heat cycle then no heat after that

  • Customer: David from Agawam MA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver, Screw drivers
  • 0 of 0 people found this instruction helpful
Replacing the cycling thermostat did not fix the problem on my whirlpool gas dryer. I then did more research on the internet and found that a likely cause was the 2 solenoids coils that control the gas valves. I replaced these and this and now the dryer works great. I had no idea how to open up the dryer to get at these, so it took a little while to figure out. 1) Lift up on front of dryer top to pop top off of 2 spring clips. 2) Reach down through top opening and find 2 bolts that attach dryer front to dryer body and remove with a nut driver. 3) Lift up on dryer front to release it from 2 hooks that it hangs on. 4) Remove 2 screws for bracket that holds coils in place. 5) Unplug coils and put in new ones. 6) Reinstall in reverse order. Problem solved. Great service from your site. Received parts 1 day after order using regular ground shipping.
All Instructions for the 7MMGD6630TQ0
511-525 of 899