7MMGD6630TM1 Dryer - Instructions

Followed instructions that came with the dryer with the exception of the idler pulley which I didn't install because this maintenance kits idler pulley does not match my dryers. Not even close. I would have had to cut or drill holes to make it work. Since I knew it was the rollers that were the problem. Dryer worked great once I was done, but it probably would have been cheaper for me to order the parts individually without the Idler Pulley if I wasn't going to replace one.

2 screws at lint tray 2 screws on back pick up top 2 screws in front under top lid separate front from drum slip in new belt screw front back to top route around tension pully put other 4 screws in complete so dry something

Popped top up Took front panel screws out. Looked for other damage. Put belt around the tumbler and got it hooked up. Grew an extra set of hands and re assembled front the checkd seals to make sure they where on and put top back down... Process is a pain in the butt i reccomend socket set channel lock pliers and a cold beverage or two

Removed top and front panels, lifted front of drum, slid new belt on drum then thru tension and motor pulleys. reassembled.

After getting on-line to your site we looked up what the problem could be after receiving the dryer from a friend to transfer from electric to gas to save money. First we thought it to be the ignitor and after receiving it so quickly it still didn't work so went to your site again and found the Flame sensor. They were both defective and now it works wonderful!!! Your site also explains what and how to repair the appliance, which my husband appreciated! We are glad you contacted us because your site did not show that we could send you and e-mail Thanking your company for the excellant service we received. Your prices can't compare to other companies either, we were amazed on the differences. When you say the next day delivery, you mean the next day!!! Thankyou and you are now in my Favorites if ever needing parts for other appliances we own.

took out old put in new

take'm apart put e'm back together

quite simply I followed the path that was worn from years of use. it was very apparent the belt had broke. along with the belt there was a generic diagram for proper install. this was very helpful

Removed back cover,top,lower and upper front,and drum. Cleaned dust and dirt drom all of the removed parts and then removed the "lint tube". Took the tube apart to clean out dirt and lint, cleaned the lint off of the motor and blower wheel, and then removed the support wheels. Installed the "lint tube" and then the new support wheels with the new locks and then installed the new belt onto the drum. I had to support the drum in order to correctly line up the belt, and then installed the upper front panel. plugged in the power cord and started the motor to be sure everything was OK before closing up the rest of the cabinet. All was OK and the belt tracted perfectly. Installed the lower front panel, top, and the rear panel. Installed the gas connection, checked for gas leaks and installed the dryer back in place. checked operation with a batch of wet clothes and the dryer worked "better than new"!!! The instruction sheet was "spot on" for clarity and accuracy.

Opened dryer top, disconnected door wireing, took off front panel, laid dryer on back, cleaned out lint and inside, put new belt on, and put parts back together. Dryer works fine now.

Remove Filter and (2) phillip screws. Use common screw driver to pry top from cabinet. Fold top back. disconnect door switch and removed (2) screws holding front of cabinet and lift frong slightly to remove from cabinet. Remove broken belt and discard. check rollers for freedom and placed drum on rollers. guided belt through idler and around motor pulley. lift front and placed on lower hooks. Lift drum and installed (2) screws that holds front of cabinet to main cabinet. connect door switch and check drum for freedom of turn. turn drum several times to get belt to center. Closed top and replaced (2) screws that hold filter door in place. Install filter and test run dryer. Completed job in about 38 minutes.

I followed the instructions supplied with the belt. I've changed the belt before so was familiar with the repair. The toe panel clips for my model had changed so what was supplied was different than the originals. Although they, too, came with instructions, they did not fit my appliance. They were inexpensive so I scrapped them and used some self-adhesive Velcro fasteners I had in a junk box.

I replaced the Cycling thermostat. At first I thought I may have blamed the wrong part because the ohm meter read almost the same for the old and the new part. It took less than a day for the part to come probably because it came from Jacksonville. I haven't guessed how much I saved by not calling a appliance repair.

belt # 346995. part was delivered quickly. Part fit perfect, no problem. there was a video on youtube how to replace it. It took about 25 minutes from start to finish to install. works like a new one. Thanks partselect.

I had to opcn up dryer, remove drum and replace worn parts.