Models > 7MGHW9150PW1

7MGHW9150PW1 Whirlpool Washer - Overview

Get Parts and Repair Help for 7MGHW9150PW1

If you know the washer repair part you need, you can browse the list of all parts on the 7MGHW9150PW1, or you can search by name or part description. You can also find your part by where it is located on the 7MGHW9150PW1 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your washer. We’ve also included any installation videos we have for 7MGHW9150PW1 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

Search for parts
Keep searches simple, eg. "belt" or "pump". Need help?
$24.50

Door Handle

This handle may appear white, but is light gray in color called Platinum.

$22.61

Drum Baffle

Sold individually. This part moves the clothes around inside your dryer/washer and helps to direct the flow of hot air during the drying cycle.

$102.80

Bellow

This part is also called the Door Boot Seal. It's the main seal between the front bulkhead and the outer tub. Clamps are not included. Must order clamps separately, if needed.

$23.46

Control Knob

This knob is light gray and is used on platinum-colored models. Sold individually and accepts a D-shaped shaft.

$73.55

Door Lock Latch

This part is used on front load washers and includes the interlock switch assembly.

$148.21

Drain Pump Kit

This pump helps expel water from the washing machine and is activated after the spin speed is maintained for a specific period of time. This part is used on front load models.

$53.75

Water Inlet Valve

Used with some front load washers. The attaching solenoids on the valve open and close according to the desired temperature, or amount of water needed.

$29.36

Shock Absorber

Shock absorbers help keep the washer from vigorous shaking during its cycles. Note: They are sold individually. Order quantity needed.

$17.08

Bellow to Outer Tub Clamp

Used to help hold your bellow in place on your washer.

$14.54

Bellow Clamp

This is used to help hold the bellow in place.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Bellows were moldy, needed to replace

  • Customer: Franck from Annandale VA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required:
  • 190 of 205 people found this instruction helpful
The first step is to remove the retainer ring that holds the outside of the bellow in place.
To do this, Open the washer door as far as you can to get it out of the way. look underneath of the front of the bellow on the outside of the washer where it meets the door. Put your head almost on the floor and look up.
You will find a spring streached... read more

Washer would not drain ,F02 and SUD code displaying

  • Customer: Donald from Wichita KS
  • Difficulty: A Bit Difficult
  • Time to Complete: 1- 2 hours
  • Tools Required: Pliers, Socket set
  • 87 of 91 people found this instruction helpful
(1) First I unpluged the washer then I removed the water from the tube with a water vac.(2) Then I removed the three (3) screws that holds the front panel, using a Torx T-20 socket. ( this is a front load washer ). The panel is below the loading door.
(3) I packed towels under the washer.
(4) I slowly removed the cleanout in the front of the p... read more

front load washer latch replacement

  • Customer: James from Vilonia AR
  • Difficulty: A Bit Difficult
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver, Screw drivers
  • 64 of 76 people found this instruction helpful
1. remove the three screws from the top backside of the top panel
2. push the top panel to the rear 1/8 to 1/4 inch
3. lift/rotate top panel from rear to front, set aside.
4. remove the three wire connectors from latch.
5. use #15 Torx to remove the three screws from the latch.
6. remove and replace part using top opening.
7. r... read more