Models > 7GU3600XTSY0

7GU3600XTSY0 Whirlpool Dishwasher - Overview

Get Parts and Repair Help for 7GU3600XTSY0

If you know the dishwasher repair part you need, you can browse the list of all parts on the 7GU3600XTSY0, or you can search by name or part description. You can also find your part by where it is located on the 7GU3600XTSY0 by selecting a section below. If you’re not sure which part you need, you can narrow your search by selecting a common symptom and we’ll show you the repair parts most likely to fix your dishwasher. We’ve also included any installation videos we have for 7GU3600XTSY0 parts. Installation instructions provided by other do-it-yourselfers will help guide you through your repair.

$22.27

Door Balance Link Kit

This kit includes 2 door balance links and 2 door balance mounts with wheels.

$45.00

Water Inlet Valve

This water inlet valve should be located behind the lower kickplate panel in either the right or left corner. The attaching solenoids on the valve open and close according to the desired amount of water needed.

$8.07

Mounting Bracket

Sold individually.

$20.38

Chopper Assembly

This chopper assembly chops/minces the food particles to prevent clogging of the dishwasher pump.

$3.76

Rack Track Stop

Used for upper dishrack track.

$3.61

Upper Rack Wheel and Mount Assembly

Sold Individually.

$21.38

Bi-Metal Fuse

This part is used as a safety device to protect the dishwasher circuit from overload. If the temperature gets to high it will shut off the electrical current to the heating unit i...

$14.90

Rinse Aid Cap

$15.27

Spinner Kit

This is also called the 3rd-level spinner. This part works like a little spray arm at the top of your dishwasher.

$3.96

Rubber Washer

Sold individually. Used with the heating element.

Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 265 of 270 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough. read more

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 175 of 184 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to th... read more

Loud grinding noise from water pump

  • Customer: Steve from Inver Grove Heights MN
  • Difficulty: A Bit Difficult
  • Time to Complete: More than 2 hours
  • Tools Required: Nutdriver, Pliers, Screw drivers, Wrench(Adjustable)
  • 88 of 95 people found this instruction helpful
Rather than remove the pump assembly - as an earlier post had done - I pulled the entire dishwasher out and laid it down on the floor. This allowed easy, direct access to the motor (that was the hard, messy part). From this point it was easy. Unplug the wiring, remove the retaining bolt, rotate the motor off the mounting brackets and pull it out. Then put th... read more