Models > 7GU3200XTVY4 > Instructions

7GU3200XTVY4 Whirlpool Dishwasher - Instructions

All installation instructions for 7GU3200XTVY4 parts

These instructions have been submitted by other PartSelect customers and can help guide you through the dishwasher repair with useful information like difficulty of repair, length of repair, tools needed, and more.

All Instructions for the 7GU3200XTVY4
1-15 of 441
Search Instructions
Keep searches simple, eg. "belt" or "pump". Need help?

Replaced Hinge Link

  • Customer: Scott from Fort Lauderdale FL
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 261 of 266 people found this instruction helpful
Pulled dishwasher from under counter, attached link to spring, hooked spring back into frame/chassis, threaded link through pulleys, attached other end of link onto door, reinstalled dishwasher under counter. All's well. Note-I purchased an extra link anticipating that the other one will fail. They're cheap enough.

Dishes on top rack of dishwasher were not being cleaned.

  • Customer: Bill from North Richland Hills TX
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Pliers
  • 172 of 181 people found this instruction helpful
1) Remove top and bottom dish baskets from the dishwasher, this will give you room to work. To remove top basket there are clips at the end of the slide rails.
2) Remove lower spray arm by unscrewing plastic screw, it should only be hand tight.
3) In order to remove the strainer cover, you will need to remove the plastic tube that takes water to the middle and top spray arms. Unclip this tube from the top and middle clips and then work it out of the strainer assembly tube. Now you should be able to remove the tube at the bottom of the dishwasher by unscrewing it 1/4 turn.
4) Remove the strainer cover by unscrewing the 4 Torqs screws.
5) You will now see two smaller torqs screws that hold the hold the Chopper Assembly cover down. Take these two screws out and remove the two piece cover.
6) Pull out the broken Chopper Assembly, make sure you get all the pieces!
7) Install the new Chopper Assembly. Make sure that you install the Assembly with the small part of the screen towards the bottom of the housing. Also make sure you compress the spring as you install the part. I used a small pair of neddle nose pliers to compress the spring behind the screen in order to install the chopper assembly.
8) Put everything back together and make sure it works!

Door spring link broken

  • Customer: Sean from Ramona CA
  • Difficulty: Easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Screw drivers, Wrench(Adjustable)
  • 83 of 85 people found this instruction helpful
1. Open the dishwasher and remove the two plastic grommets about halfway down on either side of the opening. Then remove the two screws under the grommets.

2. Remove the kick plate under the door. May have to lower unit by turning the feet using the adjustable wrench.

3. Make sure you have enough slack in the water input line and electrical wiring that you can pull the dishwasher out about 12 inches or more.

4. There is a spring and nylon rope link on both sides of the unit. Probably just one link is broken, but the replacement comes with two, so you can replace both or save one as a spare. Look at the good side and it should be pretty self explanatory how it attaches. I found it easiest to first thread the link around the lower pulley, then attach the link to the spring, then spring to the rear support, then the link to the door.

5. Reverse (2 to 1) to reinstall the dishwasher.

dishwasher not draining after wash cycle

  • Customer: Andrew from Alexandria VA
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 82 of 90 people found this instruction helpful
Caviat: The actual repair is less than 15 minutes, but I spent a lot of time playing with it before I figured out it was that easy and fast. You don't need to remove the dishwasher from the counter to do this. And it will probably help to look at the new part closely so you can understand where the retainer clip is to press it and release the old pump.

First remove the water from the dishwasher pan that would not drain with a wet/dry vac. Otherwise the water will all drain on the floor when you remove the pump. Then remove the two screws on the kickplate on the front of the unit below the door. Remove the kickplate/maintainence access cover. The drain pump is on the right about 8 inches in. Using two hands you grasp the drain pump with your right hand and use the left hand to push the retaining clip down. Then the drain pump will rotate 1/4 turn counterclockwise and can be removed without pulling the dishwasher out. There is likely to be some water leak out that was traped in the pump housing that you can not reach with the vac. Disconnect the wire. Connect the wire to the new pump, put it in place and 1/4 turn clockwise to install it. Replace the kickplate and you're done.

The door would drop open when it was released

  • Customer: David from La Quinta CA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Nutdriver
  • 61 of 63 people found this instruction helpful
This was the second time I had this problem so I knew the symptoms and remedy. The tools needed were two nut drivers a ¼” and 5/16” along with a flat pry bar and Phillips screw driver. I started by removing the lower front panel by removing the two ¼” screws on either side. The lower panel will lift up and then can be removed by pulling on the bottom. There is a flat sheet metal piece behind the front panel with insulation that can be removed very easily along with the front panel. When the front panel is removed it exposes the front legs that may need to be dropped to let you lift the dishwasher over the tile (if you have ceramic tiles). The next step would be to remove any ties to the counter top if it is attached. Mine were attached by the two straps on either side with Phillips screws. After the top is free, lower the front legs by lifting the dishwasher with the flat pry bar and threading the legs up into their holders. With the legs lifted the dishwasher can be pulled out to expose the tension springs located along the sides at the very bottom. Chances are the ropes are broken off the plastic holders that fit over the door hooks.
Remove the plastic guides by removing the 5/16” nut from the middle of the lower roller. Remember to note which hole the screw is coming from this also sets the tension for how fast or slowly the door drops. Placing the nut closer to the front will drop the door slowly and toward the back will drop the door more quickly. I placed mine in the middle hole. When the plastic guides are removed attach the nylon pope to the spring and attach to the back of the dishwasher. There is a hole located on a flat piece of sheet metal the spring will attach to at the back of the dishwasher (if it is broken). Check the other side if it is still in tact. With the spring in place weave the rope around the plastic guides then pull the springs to help get the plastic end over the door hook located at the bottom of the door. Repeat this operation for the other side (kit has a both sides covered) and reinstall dishwasher in cabinet.
Steps
1) Remove front panel (1/4” nut)
2) Release Dishwasher from Cabinet
3) Lower front legs
4) Pull Dishwasher out from under Cabinet
5) Remove Rope Guide (5/16” nut)
6) Install new Rope Guide (Supplied in Kit)
7) Attach new rope to Spring and attach spring to dishwasher
8) Weave rope through rope guide
9) With door closed pull spring to relieve tension so rope can be attached to door
10) Repeat for other side (Kit has both sides)

would not turn on

  • Customer: Douglas from Dallas GA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 54 of 67 people found this instruction helpful
I did a search on the website and read the instructions for trouble shooting. I took the inside door off by taking the screws out. I pulled the part and tested it and found it did not in fact have no ampage. I then ordered the part on line. It came in two days, I plugged it in, put the door back together and the total time was about 15-20 minutes. Easy, simple, great instructions and the entire thing only costed me the part itself. It's working great now! And I've never worked on appliances before.

Burning smell from dishwasher

  • Customer: Jeff from Blaine WA
  • Difficulty: Easy
  • Time to Complete: 30 - 60 mins
  • Tools Required: Screw drivers, Socket set
  • 41 of 45 people found this instruction helpful
So one day passing the dishwasher while it was running, I noticed a rather pungent burning smell. Yikes, I shut it off!
I took apart the pump housing at the bottom inside the dishwasher, expecting to find some kids toy plastic bit had got caught and had jammed the motor or something. But nothing there, and my dishwasher has a little screen to keep just such things from getting to the pump anyway. Hmmm.
So, ran the dishwasher again, seemed ok now.
A week later, same thing, burning smell. Pull it apart again, but no sign of trouble. But I know something is up, so I pull the kickplate and have a look underneath... Way at the back I see a red wire that looks a little melted, but it's hard to tell, so I pull the whole dishwasher out. Sure enough, one of the heater wires is melted and burned, and the plastic locknut holding that side of the heater is badly scorched. Looks like a little electrical fire, I'm lucky it didn't get out of hand!
The heater still tests ok with an ohmeter, but I don't trust it now - order the heater and replacement locknut and washers. Didn't need to order washers, they come with the heater, oh well.
Heater removal and replacement is very straight forward, but I added some high-temp gasket silicone sealant (Ultra Blue) around the seals as I think the original problem may have ben a bit of water leakage causing a short.
Took about an hour to pull the dishwasher out, remove the heater and install the new one, put a new terminal on the heater wire, and put the whole thing back under the counter.
Working great now. But not a problem I expected to have with a 2-year-old dishwasher!

Dishwasher leaked under right front corner. Discovered that overflow(float switch) was either sticking allowing fill to overflow or rubber gasket was deteriorated allowing water to leak through mounting hole.

  • Customer: Robert from Rochester NY
  • Difficulty: Really easy
  • Time to Complete: 15 - 30 mins
  • Tools Required: Wrench(Adjustable)
  • 35 of 38 people found this instruction helpful
Removed mushroom shaped float cover by simply pulling up. Cover simply slide down into switch which is mounted through the floor of the tub. Using an adjustable wrench loosened and removed plastic fastening nut allowing removal of switch assembly from below. Disconnected two wires from switch and attached replacement assembly, reinserted in mounting hole, reattached nut from top, reinserted float cap and job done! The only tricky part is that the switch needs to be mounted inside assembly, wires connected and snapped shut before reinserting. Not difficult once you figure it out, Also need to make sure rubber washer is inserted on the overflow tube before reinstalling. Keep track as you remove and simply reverse the order. Tried to obtain part locally and was told it would be 6-10 days before delivery. Order from Part select arrived in 2 days.

spinner kept falling off

  • Customer: paul from erie CO
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 37 of 46 people found this instruction helpful
i removed the top screw for the water input to the spinner, which gave me enough room to replace the worn nipple pin that the spinner snaps on to. then snapped the new spinner in place. and then screwed everything back into place.

Cap came off and melted

  • Customer: James from Mesquite TX
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required:
  • 32 of 32 people found this instruction helpful
Opened door and installed cap. Not much effort. But really got good service from Parts Select. Received order much faster than I had expected.

Plastic catch that releases the soap dispenser door broke off, the soap dispenser door wouldnt stay shut.

  • Customer: Patrick from Byron Center MI
  • Difficulty: Easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Nutdriver
  • 29 of 40 people found this instruction helpful
Removed the screws holding the metal front of the dishwasher on, removed the 6 screws holding the dispenser in place. Put the new part in and put all screws back in where they were. Put the front back on the dishwasher with its screws, done.

dishwasher cut off during drying cycle

  • Customer: pauline from gloucester VA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 22 of 25 people found this instruction helpful
After replacing the thermal fuse 5 times i noticed the new packaging came with a terminal block on then fuse harness. PLEASE USE THIS. It is a must, it supposedly is acting as some type of heat sink or something for added protection. Used the unit on all cycles now and works great. Just follow fuse instructions precisely. Hope it helps.

Borke the spinner off with dishes that were too tall. (Oops!)

  • Customer: Stephen from Leavenworth KS
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 20 of 20 people found this instruction helpful
1. Put a towel over the bottom of the machine. (In case you drop the screw... duh!)

2. Remove the top screw.

3. Replace the snap pin (pointy end DOWN.)

4. Snap the spinner in place.

5. Replace the screw. (Or go to the hardware store to replace the screw you dropped into the bottom of the dishwasher. Dashitall!)

Dishes still dirty after full cycle. problem developed gradually over 2 week period

  • Customer: Jeff from Vallejo CA
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 21 of 24 people found this instruction helpful
Several hours to diagnose problem: Removed all the plastic water distribution tubes to top rack and found no blockages. removed lower water jets, drain screens using star driver on 6 screws. still could find now blockages. decided problem had to be in pump mounted below unit so completely disconnected unit and removed from under counter. Upon removing lower plate below door I discovered a plastic pouch containing an excellent trouble shooting guide with complete dis-assembly instructions and parts breakout diagrams with P/N listings! First thing I discovered from this was that the chopper assembly was hiding under a plastic cover just under the filter screen I had already removed. The trick was to press down on the right side of the plate to get it to pop up and reveal the chopper. The whole chopper assembly slides out without tools. I found the strainer plate behind the chopper blade totally plugged as the blade had broken off the plastic drive shaft because the retaining knob on the end of the shaft had broken off. I was able to drill and tap the shaft and install a SS machine screw with washer to reassemble the chopper blade on the shaft. Not expecting this "Joe Maggee" repair to last more than a few cycles I went online with the P/N and googled PartSelect. Placed the order and chose std delivery over 2day or next day since I expected the repair to last for the week. I put everything back together and the first load came out perfect! This was Sunday afternoon. Tuesday the part arrived at my doorstep! 15 minutes and the new part was in. My "Joe Maggee" repair is now in the junk drawer awaiting the next pistachio shell that gets run through the washer.

No water out the spray arms; first thing you'll notice is the top rack not getting clean.

  • Customer: Brian from Inola OK
  • Difficulty: Really easy
  • Time to Complete: Less than 15 mins
  • Tools Required: Screw drivers
  • 19 of 20 people found this instruction helpful
Took racks out, loosen screw on top and back then twist feed tube to right and whole assembly can be removed. Now you should be able to see some torx screws; remove those and then remove the piece they were holding down, from there you'll see another screw, remove it and the piece and so on until there are no more screws. Now there is the food chopper cover that needs to be removed; mine was stuck there. You should notice some ribs underneath that allow the water to be sucked in while keeping really big pieces out; I got a pair of channel-locks, opened them all the way and was able to slip one of the pieces under the cover and pull straight up, once off you will see the chopper covvered in food. I cleaned mine off and it looked good, but when I put it back and stuck my finger down teh discharge tube and turned the pump, the chpper did not turn. when I put the new one in and did the same test it did turn. If the chopper is still fits in the slot, it can be cleaned and put back and work for several washes while the part is shipped. I went ahead and changed the check valve since I had it opened which is just to the right of the chopper(all you can see is a little slit and some black rubber). Use some needle nose and pull it out. I would not do this unless you plan on changing it, I pulled mine out to look at it and when I put it back so I could order the parts the dishwasher never drained properly. When you compare a new one with an old one you will see what I mean, you can drop a new one right in but the old one you will have to force in (gets water logged over time and expands). This job is very easy and a lot cheaper than a new DW...and your wife will be impressed, so do not be intimidated.
All Instructions for the 7GU3200XTVY4
1-15 of 441