7GU2300XTVS3 Whirlpool Dishwasher - Instructions

I first checked the power to the dishwasher. Then searched the web. I found a video that described the problem. I found the cut-off fuse and tested the conductivity -- it was blown. So I ordered the thermal cut-off fuse for the dishwasher. It came in 2 days! It was easy to install. You take the cover off the door and pop the cover off the controls; cut the wires; install the new part; and put the door back together. Actually the hardest part was getting the door back together. Worked fine first time.

Simply remove the front cover of the dishwasher, attached by 6 screws. This is where you'll need a TORXhead (star shaped bit) screwdriver. Once the cover's set aside, you'll see a plastic flap covering the dispenser. Unplug the wire connector from the bottom of the dispenser & unscrew 6 small screws with a nutdriver or small socket wrench. The OLD dispenser will be be removed from 'inside' the door & the new one installed the same way. Holding the NEW dispenser in place with one hand, start your screws back into it from the outside, making sure it remains properly aligned. *Be sure to insert the plastic cover flap onto the outside of the dispenser, BEFORE reattaching the holding bracket. Plug in your wire connector & reattach the washer's cover. It may sound difficult from this, but it's SUPER SIMPLE, & my wife now KNOWS I'm WONDERFUL, cuz we saved a BUNCH of money by me doing it, instead of a washer repairman. Good Luck!! RJ

Very easy, followed the instructions from former customers. Thank you for the quick delivery, I received the part the day after I ordered it.

I had purchased a used home near my new place of employment in a new state. The house was pretty nice and my wife even approved of my choice. After moving in we noticed that several little things were wrong with the dishwasher. I did some research at the website of the manufacturer which linked me to PartSelect.com. After finding the missing parts, they arrived only three days after I ordered them. Within a few minutes, without having to use any tools but my hands, the parts were installed and now my wife is a very happy lady! Thanks, PartSelect.com!!!

I just attached it to the top rack by using the other pivot clips as an example.

slowly

Empty dishwasher remove bottom basket. Disconnect electricity then turn off water. Remove top screws from counter. Slide unit out and gently tip forward. Remove the two wires from connectors on element. Unscrew plastic nuts from element save if reusable. Gently tilt unit back to normal position. Remove old element and install new one and attach to stainless spacers to hold element in place. Tip unit forward. Reinstall plastic nuts. Plug wires back into new element connectors. Tilt back into normal position. Turn water back on check for any leaks and repair if necessary. Turn electricity back on and then slide unit back into original position and replace under counter screws. Test out by running quick cycle wash. It should function normally. During drying cycle open door to be sure it is hot inside. If hot then it is repaired. Let it finish cycle and replace basket. Do not touch hot element as it will burn you.

Changed the control panel and the unit still did not work. Thought maybe it was the door switches - ordered the wrong part - tried the Thermal Cut Off(tco) replaced it and the unit works great.

After finding out how to replace it (on YouTube)the repair went smoother than anticipated. the difficulty was disconnecting/connecting the electrical(BX to electric hook-up to dishwasher) due to the proximity of where it was located(~1" from the floor). Other than that, the unit now works as good as the 1st day when it was bought(~6yrs ago)

Using a Torx screwdriver, I removed the fasteners holding the control panel/latch section of the door on the dishwasher. I tested the high limit thermostat with a multimeter. Just two terminals, one being power in, the other power out. The part had what I have heard call a "high resistance open". In other words, the power was not getting from "A" to "B". Power in - not out. After cutting power to the unit, I removed the part (just pull it out of the retaining clip and pull the terminals from the part). After receiving the part...by the way, really fast delivery...I reconnected the part (it doesn't matter which wire goes where), pushed the part back into the retaining clip, replaced and fastened the control panel, then restored power to the unit. Runs like new.

Diagnosing the problem was made easy using the "8 things that could be wrong" if the dishwasher would not turn on in the "Instant Repairman" area. We were going to order the entire module replacement for $141. Then we saw the Q & A link that said the Bi-Metal Fuse had the highest percentage of repairs if exhibiting such symptoms as our machine exhibited. The price of the fuse was $25. WOW what a difference in price and yes, it did fix the problem. The help given through the "Instant Repairman" area of the website saved us from spending $141 when $25 fixed our problem. We have ordered several parts but didn't know about the the "Instant Repairman". We will never again NOT use it to diagnose a problem.

Shut off water,power. disconnect water line,electric,drain.Pulled dishwasher out,laid dishwasher on it's back.Unplugged electric on pump,twisted pump out.Installed new pump and reinstalled dishwasher.

With a flat blade screwdriver, pry up gently on the Upper Rack Track, pull out the end caps, and remove the rack. Pull the Feed Tube down out of the clip in the ceiling, Install the Upper Wash Arm on the Feed Tube, insert the Push-In Screw from below and push the Screw Cover down from above to snap everything together.

I also replaced the Lower Spray Arm Seal. First remove the Lower Dish Rack then remove the Lower Spray Arm by grasping the Lower Spray Arm Support/Hub and twisting the arm counter-clockwise to unscrew it, Pull the arm and hub out, now twist the Rear Feed Cap clock-wise to dislodge the Feed Tube and disconnect the cap. The seal is underneath.

I had to drill screw heads off then take vice grips to pull out screws......you have to be very carefull not to drill too deep and loose the plastic you need to hold new screws,,,At the cost of these replacement parts I would never do it again,,,,,,,,I would have been happy if the replacement racks were of better quality than the origional racks.

The door switch did not allow for the dishwasher to reset after washing. It was an easy fix, just remove the top trim panel (6 screws) pull out the switches, replace and reassemble. Just be aware that there two switches two replace.