7DU1100XTSQ5 Whirlpool Dishwasher - Instructions

The repair was so simple. I squeezed the end part off. Took out the rack and took off all wheel mounts and replaced with new ones.

At first I thought that it was the feed tube but after some more thought I started diging and found the chopper broken cleaned the screen and got water to top tray so I ordered the chopper assembly and now it works fine

it about 30 min to replase this part it was easy as pie.

I unscrewed two plastic covers to get to the chopper. I found out that the blade fell off and could not be put back in place. As a result the filter behind it was all clogged. I replaced the whole thing with the new one and put the plastic covers back in place. The dishwasher works like a charm. The hard part was that the screws have proprietary heads, so it is hard to screw/unscrew them with a regular screwdriver. Other than that the exercise is trivial.

1. Pulled out the old gasket (very easy. slid right out).

2. Carefully noted how it went in (so I could put the new one in correctly)

3. Measured the length of the new gasket. Unnecessarily worried that the new gasket appeared to be 2" shorter than the old one.

4. Cleaned the track and the general area around the dishwasher that rarely gets clean. Took 15 minutes.

5. Inserted the new seal, making certain it was fully inserted all along the track. It was a perfect fit.

6. Patted myself on the back and bragged to my wife that the job was done.

7. Life is good.

Dave in Massachusetts

I loooked up the main problems associated with that model which is provided on the website and ended up ordering a heating element and a thermostat. I replaced both parts it took me about 30 minutes. The dishwasher is working again and my wife is very happy. Thanks guys!!!

I received these parts on the second day after ordering.Took longer to take wheels off the top rack then replacing new ones and replacing rood gasket.Very easy to do had it done within 30 minutes. No leaking around the door and top shelf slides like new.thank you

Remove the Racks. Unscrew the lower wash arm with the plastic thumb screw in the middle, set aside. Remove the water chase to the upper wash arm by unclipping the metal keepers at the back of washer and at the top.
Spin remaining water chase clockwise and lift out. Remove torx screws-4 of them. lift out lower assembly. remove one more screw that holds chopper cover in. remove chopper cover. replace /clean chopper assembly screen and any other debris in bottom of washer. install..reverse removal instructions.

Unscrew, replace, reacted

removed 2 trays and parts and 4 screws

removed parts and the ordered the parts. It was very easy to order parts from Partselect. I unscrewed a few screws and the disassembly was a breeze. I then revresed my steps and the new parts were instlalled no problem. Now on the the motor replacement. Thanks Partselect.com

I would have torn something up had I not watched the video posted here first. The spring loaded chopper is a bit tricky to get in lined up properly to get the cover assembly back on. 30 minutes and several small finger tip cuts later, and the machine cleans like new.

Installed the rubber grommet and the door was fixed.Wish the product was made to lasts,second time in three years the part had to be replaced.

Removed old gasket by pulling it gently from one side to the other, cleaned track where gasket sits, replaced with new gasket by folding in half and beginning in center at top of dishwasher, using strike plate as center guide, working left side then right side, applying pressure with fingers to push new gasket in channel. I did replace the strike plate, but the one provided did not match the one I removed, therefore, was not working properly, so I inserted the old one back in and everything works fine.....no leaks. The instructional YOUTUBE videos on the internet were a big help to watch before beginning the removal and install. Couldn't have been easier and I'm sure I saved about $150 in repair person costs for time and labor only.

Ordered parts from Parts Select. Took 2 minutes to find and order. Received order following day! What service. Snapped old wheels off and new ones on....then replaced Spinner Assembly all within 15 minutes!