7DU1100XTSQ5 Whirlpool Dishwasher - Instructions

Pulled the dishwasher out from the counter, on the lower right hand side, about mid way back there is a bundle of all yellow wires, follow that to the sensor which mounts into the bottom of the wash tub. The sensor is easily removed by grasping it by hand and turn it about a half turn (can't remember which direction). It then just pulls out. Disconnect the wire bundle by pushing on the retaining clip and the install is the reverse.

Took racks out, loosen screw on top and back then twist feed tube to right and whole assembly can be removed. Now you should be able to see some torx screws; remove those and then remove the piece they were holding down, from there you'll see another screw, remove it and the piece and so on until there are no more screws. Now there is the food chopper cover that needs to be removed; mine was stuck there. You should notice some ribs underneath that allow the water to be sucked in while keeping really big pieces out; I got a pair of channel-locks, opened them all the way and was able to slip one of the pieces under the cover and pull straight up, once off you will see the chopper covvered in food. I cleaned mine off and it looked good, but when I put it back and stuck my finger down teh discharge tube and turned the pump, the chpper did not turn. when I put the new one in and did the same test it did turn. If the chopper is still fits in the slot, it can be cleaned and put back and work for several washes while the part is shipped. I went ahead and changed the check valve since I had it opened which is just to the right of the chopper(all you can see is a little slit and some black rubber). Use some needle nose and pull it out. I would not do this unless you plan on changing it, I pulled mine out to look at it and when I put it back so I could order the parts the dishwasher never drained properly. When you compare a new one with an old one you will see what I mean, you can drop a new one right in but the old one you will have to force in (gets water logged over time and expands). This job is very easy and a lot cheaper than a new DW...and your wife will be impressed, so do not be intimidated.

As I pulled out the old rubber gasket I noticed there was a flat side and a curved side, this is how the new one must go. When I put in the new gasket in I just made sure the flat side (faced out) and it really was very simple. It just fits inside a grove, very easy to install. I compared the to parts (old and new) they were exactly the same shape and length.
I was very impressed with the web site navigation and layout. I was able to zoom in on pictures of the part and there were exact measurements of dimensions.

Very easy to install the new B Metal Fuse. Removed torx head screws holding the outer door panel on the dish washer. Removed the fuse and two wires connected to the fuse. Inserted the new fuse in the holder and plugged the two wire connectors back
on. Installed the outer door panel back on, turned the breaker back and the machine powered back up. Very easy install and saved a service call. Total repair cost $24

unscrewed dishwasher from cabinet ...,moved out slightly....while door closed ...reached with long nosed pliers door spring pulled forward...and allowing white plastic part that fits through sleeve and fit new sleeve over it...pulled spring attaching white plastic part and pushed unit back to cabinet and replaced screws DONE.

Checked grinder and cleaned it several times, adjusted blades. Dishes would be clean for approx. 6 cycles, then would not clean. Placed dishwasher on its front and removed the motor. Removed grinder and impeller which I found to be worn so that the blades would not turn on the grinder which caused it to collect food particles. The impeller locks in easily.

This product comes in a bottle with a brush like Liquid Paper. It goes on incredibly easy. A second coat might be needed. I wanted to prevent rust from setting in so I covered the scratches and dings. The paint is a little brighter since my washer is 10 years old but it still looks great.

Took the two baskets out and removed the spinners which simply clip on. The bottom center spinner screws on/off using a tab in the center. Then removed four screws holding the filter cover in place. Then removed the one screw holding on the chopper cover and removed cover. Old chopper came out easily. Then rinsed and washed everything down to clean out all of the disgusting stuff that was clogging the unit. Put the new chopper in place, put chopper cover on and everything else in place and it now cleans like it was brand new!

open dishwasher door, use torx socket and ratchet to remove 6 screws. Pull down wash options face, find the bi-metal fuse. Used the directions in the package to replace. popped old fuse out of electrical board, Cut 2 wires, stripped said wires, attached stripped wires in housing on new part, tightened the 2 screws where new wires attach, popped new fuse in electrical board. Reattached face. Very simple and easy to do. Did not fix the problem. Had to get the electrical board that the bi-metal fuse is snapped into. Very easy for someone that has worked on vehicles or electrical things before. If no experience, then I would say it is still easy as long as you follow the directions taht comes with the part. It has pictures as well.

Several hours to diagnose problem: Removed all the plastic water distribution tubes to top rack and found no blockages. removed lower water jets, drain screens using star driver on 6 screws. still could find now blockages. decided problem had to be in pump mounted below unit so completely disconnected unit and removed from under counter. Upon removing lower plate below door I discovered a plastic pouch containing an excellent trouble shooting guide with complete dis-assembly instructions and parts breakout diagrams with P/N listings! First thing I discovered from this was that the chopper assembly was hiding under a plastic cover just under the filter screen I had already removed. The trick was to press down on the right side of the plate to get it to pop up and reveal the chopper. The whole chopper assembly slides out without tools. I found the strainer plate behind the chopper blade totally plugged as the blade had broken off the plastic drive shaft because the retaining knob on the end of the shaft had broken off. I was able to drill and tap the shaft and install a SS machine screw with washer to reassemble the chopper blade on the shaft. Not expecting this "Joe Maggee" repair to last more than a few cycles I went online with the P/N and googled PartSelect. Placed the order and chose std delivery over 2day or next day since I expected the repair to last for the week. I put everything back together and the first load came out perfect! This was Sunday afternoon. Tuesday the part arrived at my doorstep! 15 minutes and the new part was in. My "Joe Maggee" repair is now in the junk drawer awaiting the next pistachio shell that gets run through the washer.

Sears could not supply us with the replacement cap for the dishwasher. We were saved by being able to get the cap here on your web page.Your web sight is like going into the garage and finding the part you saved up for many years that you knew you would need down the road.

I shut off the power to the dishwasher, then I removed the front panel under the door. On the right side just behind the electrical box there are two wires going up to the hi-limit thermostat, (you may need a small mirror to see it), remove one screw that is holding the thermostat bracket, unplug the wires from the old thermostat and install new one. Screw bracket and thermostat back to the underside of the dishwasher, reinstall the front panel, turn on the power, done.

I couldn't get dealer to order part, so went on line to see what was available. Found model and picture of part needed and ordered. It came in 3 days. Took part out of box and compared to part the needed replacing. It was a match. Removed old basket and replaced with new one. It works great and siverware stays in basket until put away.

remove front door outer cover,remove the hex screws holding the dispenser.unplug the wire to the dispenser and remove.replace with the new dispenser, fasten with hex head screws and plug in the wire. make sure you put the vinyl flap back in place. close front door cover and fasten.

First I unplugged the dishwasher.Then I removed 6 Torx screws, popped off cover, cut wires to old fuse, stripped wire, placed wires in new part, tightened screws, reassembled in reverse order, plugged unit back in and tested. WOO HOO!

I saved over $150.00 by doing it myself instead of having a repairman come out! That's 4 free fishing trips!